Honsel Rivdom eVNG2 Page 27 Operation Manual Download

Page: 27 / 32

Operation Manual

Edition: May 2021

Version 1

English

Warnings

The riveting tool has various warning messages that alert the user to certain operating

conditions or dangers. In addition to the warning message, there is also an indication of

what should be done by the user. The following warning messages are present:

Warning / Messages

RGB-LED

Foot-

LED

Descritpion

Ready

Green

Tool is ready for use

Busy

Yellow

Software menu is open

Battery empty

Red

Change battery

Overload

Red

Wait at least 10 seconds

Battery temperature low

Red

Warm the battery

Battery temperature high

Red

Change the battery

Tool temperature low

Red

Warm the tool

Tool temperature high

Red

Wait until the riveting tool has cooled

down

Service

Red

If the riveting tool has set 300,000 blind

rivet nuts / blind rivet bolts, the service

message appears. This appears again

and again until the riveting tool has

been serviced by an authorized service

company

Emergency mode

Red flashing

Tool is in emergency mode

Summary of Contents for Rivdom eVNG2

































Search results

Summary of Contents for Rivdom eVNG2

Reviews:

Related manuals for Rivdom eVNG2

Brands by name

Popular brands

Honsel Rivdom eVNG2, Operation Manual

Search results

Summary of Contents for Rivdom eVNG2

Reviews:

Related manuals for Rivdom eVNG2

Brands by name

Popular brands