Honeywell Youjie HH660 User Manual Download | Manualshive

Page: 38 / 164

background image

2 - 22

ACK/NAK

After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from the
host. If ACK is received, the communications cycle is completed and the scanner looks for more bar codes. If NAK is
received, the last set of bar code data is retransmitted and the scanner waits for ACK/NAK again. Turn on the ACK/NAK
protocol by scanning the

ACK/NAK On

bar code below. To turn off the protocol, scan

ACK/NAK Off

.

Default = ACK/NAK

Off

.

Scanner to Bioptic Communication

The following settings are used to set up communication between Honeywell scanners and bioptic scanners.

Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with

a bioptic scanner. See "RS232 Baud Rate" on page 2-18, and

RS232 Timeout

on page 2-21 for further information.

Scanner-Bioptic Packet Mode

Packet Mode On

must be scanned to set the scanner’s format so it is compatible with a bioptic scanner.

Default = Packet

Mode Off.

Scanner-Bioptic ACK/NAK Mode

Bioptic ACK/Nak On

must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet

is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response.

Default =

Bioptic ACK/NAK Off.

ACK/NAK On

* ACK/NAK Off

* Packet Mode Off

Packet Mode On

* Bioptic ACK/NAK Off

Bioptic ACK/NAK On

«
...
36
37
38
39
40
...
»

Summary of Contents for Youjie HH660





































































































































































Reviews:

No comments

Related manuals for Youjie HH660

IMAGECLASS MF4150

Brand: Canon Pages: 76

Brand: Keithley Pages: 188

Brand: Symbol Pages: 2

Brand: SICK Pages: 44

Brand: SICK Pages: 48

Brand: Bell and Howell Pages: 1

Brand: TEC Pages: 23

Brand: Plustek Pages: 31

Brand: SICK Pages: 134

Brand: Datalogic Pages: 48

Juniper System Allegro DOS

Brand: Campbell Pages: 4

Quick Check 600 Series

Brand: Hand Held Products Pages: 120

Brand: Hand Held Products Pages: 248

Brand: X-Rite Pages: 28

Brand: PageExpress Pages: 16

Brand: Xerox Pages: 68

Linea Pro 4.0 Series

Brand: Datecs Pages: 23

Brand: Uniden Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands