Honeywell XLS-REL Technical Reference Manual Download Page 48

Page: 48 / 52

XLS-REL trouble indications

4.4

XLS-REL Technical Reference Manual

XLS-REL indications on XLS1000 panels

Warning!

Disconnect all wiring on TB4 of the XLS-REL

(release circuits 1 and 2) during system service. Disabled points

will not prevent activation of the release circuits. Failure to

follow these instructions may result in loss of life, serious injury,

or property damage.

When programming is complete, the fire alarm control panel will

reset itself, reconstruct the line datacard, and map it. Upon reset,

device supervision may cause the panel to generate a common

trouble active for each XLS-REL circuit. This is a normal

indication, and it should go away within minutes. Table 4-2 lists

the indications you may see for the XLS-REL on the 3-LCD.

Table 4-2: Releasing Module indications

Device

Condition

LED

3-LCD message

Abort

Short

Monitor

MONITOR ACT (Abort)

Open

Trouble

COMMON TRBL ACT
Abort*
Expanded message: TROUBLE OPEN ACT

Manual

Short

Alarm

PULL STATION ACT
Manual*

Open

Trouble

COMMON TRBL ACT
Manual*
Expanded message: TROUBLE OPEN ACT

Prerelease_1

Short

Trouble

COMMON TRBL ACT
Prerelease_1*
Expanded message: TROUBLE SHRT ACT

Open

Trouble

COMMON TRBL ACT
Prerelease_1*
Expanded message: TROUBLE OPEN ACT

Prerelease_2

Short

Trouble

COMMON TRBL ACT
Prerelease_2*
Expanded message: TROUBLE SHRT ACT

Open

Trouble

COMMON TRBL ACT
Prerelease_2*
Expanded message: TROUBLE OPEN ACT

Abort
Manual
Prerelease_1
Prerelease_2
Release_1
Release_2

No riser

Trouble

COMMON TRBL ACT
Device (Abort, Manual, Prerelease_1, Prerelease_2,
Release_1, or Release_2)*
Expanded message: INTRNL TRBL ACT

Summary of Contents for XLS-REL




















































Search results

Summary of Contents for XLS-REL

Reviews:

Honeywell XLS-REL, Technical Reference Manual, Page: 48 / 52

Search results

Summary of Contents for XLS-REL

Reviews: