Honeywell XLS-REL Technical Reference Manual Download Page 46

Page: 46 / 52

XLS-REL trouble indications

4.2

XLS-REL Technical Reference Manual

XLS-REL indications on XLS100 panels

Warning!

Disconnect all wiring on TB4 of the XLS-REL

(release circuits 1 and 2) during system service. Disabled points

will not prevent activation of the release circuits. Failure to

follow these instructions may result in loss of life, serious injury,

or property damage.

After the successful completion of the programming process, the

fire alarm control panel will reset itself. Upon reset, device

supervision may cause the panel to generate a Dev/Line fault for

each XLS-REL circuit. This is a normal indication, and it should

go away within minutes. Table 4-1 lists the indications you may

see for the XLS-REL on the 2-LCD.

Table 4-1: Releasing Module indications

Device

Condition

LED

2-LCD message

Abort

Short

Monitor

None, unless there is another event

Open

Trouble

Open Fault
Abort*

Manual

Short

Alarm

1st Fire Alarm
Manual*

Open

Trouble

Open Fault
Manual*

Prerelease_1

Short

Trouble

Short Fault
Prerelease_1*

Open

Trouble

Open Fault
Prerelease_1*

Prerelease_2

Short

Trouble

Dev/Line Flt
Prerelease_2*

Open

Trouble

Open Fault
Prerelease_2*

Abort
Manual
Prerelease_1
Prerelease_2
Release_1
Release_2

No riser

Trouble

Dev/Line Flt
Device (Abort, Manual, Prerelease_1, Prerelease_2,
Release_1, or Release_2)*

Release_1

Short

Trouble

Short Fault
Release_1*

Open

Trouble

Open Fault
Release_1*

Summary of Contents for XLS-REL




















































Search results

Summary of Contents for XLS-REL

Reviews:

Honeywell XLS-REL, Technical Reference Manual, Page: 46 / 52

Search results

Summary of Contents for XLS-REL

Reviews: