manualshive.com logo in svg

Honeywell XLS-REL, Technical Reference Manual, Page: 38 / 52

Share
Download
Honeywell XLS-REL Technical Reference Manual Download Page 38

Programming the XLS-REL

2.14

XLS-REL Technical Reference Manual

System testing

Warning! 

Disconnect the release circuit until system testing is 

complete and the system is stable.

Testing XLS100 systems

Allow the system sufficient time to stabilize after the initial 

startup or download. Before you test the system, access the SDC 

Status tool in the XLS100-SDU. Do not test the system if the 

status LEDs indicate anything pending or in progress. This 

includes:
•

Mapping

•

Device new starts

•

Resets

•

Restarts

Testing XLS1000 systems

Allow the system sufficient time to stabilize after the initial 

startup or download. Before you test the system, access the 

DSDC Status tool in the XLS1000-SDU. Do not test the system if 

the status LEDs indicate anything pending or in progress. This 

includes:
•

Mapping

•

Device new starts

•

Resets

•

Restarts

In the XLS1000-SDU (Rev 2.0), you can test the system while 

the Device Supervision LED is on. The Device Supervision LED 

may be on longer for larger loops.

Summary of Contents for XLS-REL





















































Reviews:

No comments