Honeywell W8735ER Installation Instructions Manual Download Page 7

W8735ER WIRELESS OUTDOOR RESET MODULE

7

66-1202—01

WIRELESS OUTDOOR RESET MODULE ALARMS AND 

TROUBLESHOOTING

The W8735ER Wireless Outdoor Reset Module’s enhanced diagnostics provides information alerting of deteriorating boiler 

efficiency or if the system is not running optimally. Outdoor reset-related errors can be displayed on diagnostic tools and displays. 

Errors are also displayed on the Aquastat's 3-digit display. See Table 5 for available Outdoor reset-related error codes.

a

Warnings are generated to enunciate the system is not operating optimally, but the Aquastat is still operating and maintaining 

boiler temperature. In the instance where an Outdoor Reset Module is used, the warnings may indicate a reset curve setting 

error one or more features is not running optimally, and the Aquastat is reverting to default settings or has stopped running the 

Outdoor Reset algorithms. The warnings are cleared when the issue(s) is resolved.

NOTE: Aquastat alarms reset automatically once the alarm condition has been resolved.  Alarms can also be reset by 

cycling power if the alarm condition is no longer present.

Table 5. Aquastat Outdoor Reset Related Error Codes.

Error 

Code

Cause/Action

EnviraCOM 

Alarm

Err 9

a

Warning: Outdoor Reset System failure; communication to Outdoor Reset Module lost, Outdoor 

Reset Module failure, multiple outdoor temperature sensors detected on the bus, or outdoor 

temperature sensor failure. Check EnviraCOM wiring (1, 2, 3), check sensor wiring.

50, 53, 149

Err 10

a

Warning: Boost Failure; Boost Mode active at least once per cycle for the last 60 consecutive 

cycles. Check Outdoor Reset curve settings.

150

Err 11

a

DHW Module Sensor failure.

Warning: DHW System failure; communication to DHW Module lost, DHW Module failure, or 

temperature sensor failure. Check EnviraCOM wiring (1, 2, 3), check sensor wiring.

146, 147, 148

Table 6. EnviraCOM Outdoor Reset Alarms and Troubleshooting.

Alarm Desription

EnviraCOM 

Alarm

Troubleshooting

Duplicate Outdoor Temp Alarm Present

50

Only one outdoor sensor (wired/wireless) is allowed.                                                                                                                                    

Ensure no other outdoor sensors is connected.

Outdoor Temp Sensor Low Battery Alert

156

Replace sensor batteries

Outdoor Sensor Missing/Failure

53

Outdoor sensor failure.  Replace sensor.

Missing Outdoor Temp Sensor

149

Module not bound within 5 minutes of power-up or lost once 

enrolled. Check batteries

Summary of Contents for W8735ER









Reviews: