background image

T8601D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS

69-1626

8

NOTE: Press any key and the displayed numbers 

change. Press Time 

 to go to the previous test 

and Time 

 to go to the next test. The Run Pro-

gram key does not exit this test. Press Time 

 

or Time 

 and then the Run Program key to 

exit.

THERMOSTAT INFORMATION

1.

Press the Time 

▲ 

key to access the thermostat 

information.

2.

Press the increase 

 key to display the production 

date code. The first two large digits are the month 

and the third digit is the last digit of the year (Exam-
ple: 027=February 1997).

3.

Press the increase 

 key again to display the soft-

ware identification code. (Example: 02 = software 

ID code 2).

4.

Press the increase

 ▲

 key again to display the soft-

ware revision number (Example: 001=Revision 

number 1).

5.

Press the increase 

 key again to display the 

EEPROM identification code. (Example: 314 = 

EEPROM ID 314).

6.

Press the Run Program key to exit the self-test. 
The self-test times out after four minutes without 

any key presses.

CHECKOUT

Outdoor Temperature Sensor 
(select models)

Allow the outdoor temperature sensor to soak in the 
outdoor air for a minimum of five minutes before taking a 

reading.

TROUBLESHOOTING GUIDE

Refer to Table 6 for troubleshooting information.

Cooling Equipment System Test

Time 

30

Change from heating to cooling 

equipment system test

31

Cool and system fan come on

30

Cool and system fan turn off

Fan Equipment System Test

Time 

40

Change from cooling to fan 
equipment system test

41

Fan comes on

40

Fan turns off

Key Equipment System Test

Time 

60

Change from fan to key operation 

system test

Table 5. Installer Self-Test Options.

Key to 

Press

Test 

Number

Description

M14615

M14616

M14617

Summary of Contents for T8601D













Reviews: