–
+
OK
menu
–
+
OK
menu
Radio thermostat for thermostatic
radiator valves
z
Settings button
–
(press briefl y) and to go back or
cancel (press and hold)
Settings button
+
(press briefl y) and OK button for
confi rmation of settings (press and hold)
Short press on A+B = menu access
EK760
A
A
B
B
3
2
1
6LE001855B
Description of the thermostat
The EK760 thermostat is designed to provide
comfort and energy savings, and is easily installed
on thermostatic radiator valves. It regulates the
ambient temperature and works in association with
a home automation controller, such as TKP100A
and/or with radio transmitters in the TRMxxx
range, allowing you to benefi t from the associated
functions of programming, check and visualization.
It allows the heating device to regulate according to
3 temperature levels:
• Comfort
: The desired temperature when you
are present within the room.
• Night setpoint
: The desired temperature during
short absences or at night.
• Frost Protection
: The minimum temperature
ensured during extended periods of absence. It
protects your house from the risk of frost.
1
Display (temperature / text)
2
Ongoing temperature bypass indicator
3
Open window
4
Ongoing presetting indicator
5
Frost protection mode activated
6
Night setpoint heating mode activated
7
Comfort heating mode activated
8
Temperature indicator in °C
9
Low battery level indicator
A
Safety locking activated
Z
Radio link confi guration indicator
Installation and replacement of batteries
Remove the cover of the battery box by pressing
the cover upwards at the marked location (1) and
picking it up (2).
Then, place the batteries in the direction indicated
at the base of the product.
AA
Changing the batteries has no infl uence on the
confi guration of the product.
O
Never use new and old batteries together;
nor should batteries of different brands be
used together.
Do not use rechargeable batteries!
Respect the correct polarity!
Initial confi guration
Once the batteries are fi tted, you can select the
language used on the EK760 (English, French,
German, Italian). The default language used is
English, however you can change this selection by
pressing on the " + " / " - " keys briefl y, then confi rm
the selected language by pressing and holding on
the "OK" key.
Installation
After the batteries are inserted, the motor is com-
pletely pushed upwards in order to facilitate instal-
lation. The screen will display
INST
(INST may also
be selected from the menu, at all times). Ensure
installation only in this position. Do not press the
other keys, and the thermostat is ready to be fi tted.
Withdraw the head of the original thermostatic valve
(caution: only the thermostatic valves can be con-
trolled by the EK760 thermostat). The installation
process is to be carried out without contact with
dirt or water as the valve body remains in place.
The EK760 is fully compatible with existing
thermostatic valves using M30x1.5 threading
(Honeywell, Landis & Gyr, TA, Heimeier, etc.) using
the white coupling ring provided.
In case of Danfoss valves, it is necessary to use
an adapter provided in addition to the white ring
(please refer to the correspondence table below).
Heimeier, Junkers Gyr,
MNG, Honeywell, Braukmann
measured thread : M30x1,5
No adapter needed
Danfoss RAV (The pin joint
must be attached to the valve
tappet)
+ Mounted pin
Danfoss RA
Danfoss RAVL
Before installing the adapters, fully remove the
protection pins marked in grey on the drawing.
If the model of the valve is different from those
listed above, you must use an optional adapter
listed below:
• EK771 for COMAP M28x1.5 valve
• EK772 for Oventrop M30x1.0 valve
• EK773 for Vaillant valve
• EK774 for Herz M28x1.5 valve
• EK775 for Giacomini valve
Press and hold on the "OK" key until
INST
disappears so that EK760 can start its installation
process. The device adapts to the operating
range of the valve. In some cases, this procedure
may take several minutes. Once the adaptation is
completed, the EK760 goes back to the normal
operating mode.
• If a new adaptation is necessary (for example if
your radiator does not cool down while in
summer mode), select INSTALLATION from the
menu until adaptation starts.
• If error
ERR2
appears on the screen, fi t the
EK760 on the radiator valve and then briefl y
remove the batteries to reinitialize.
Removal
To remove EK760, set the device in
INST
position
(Please refer to the above chapter), wait for a brief
moment and then press on the release lock located
in the groove in the lower part with the fork tool
delivered to disconnect.
Subsequently, remove EK760 from the valve body.
Radio Link confi guration
The next step is to confi gure the radio link of EK760,
to do so there are 2 options:
1. Using a house automation controller such as
TKP100A, place TKP100A in product append
mode, and cfg will appear on the EK760 screen
and RF confi guration will be displayed
subsequently. Press and hold on "OK" to start
the link process. At the end of the process, it is
carried out correctly if the display indicates "OK",
on the other hand the operation must be
repeated if it indicates "NOK" (For more
information, see instructions for TKP100A).
2. Using micromodules of type TRM69x or TRM702A,
place the micromodule in confi guration mode,
and cfg will appear on the EK760 display screen
subsequently. Press and hold on "OK" to start
the link process. You can select the
desired function by navigating with the "+"
/ " - " key then confi rming the function selected
by pressing and holding on the "OK" key.
**
* Function not available with TRMxxx radio
transmitters.
While setting up the radio link, the display will fi rst
indicate "
Link
". Then, it displays "
OK
" if the radio
link has been successfully established or "
NOK
"
if it has not been successfully established. In this
case, repeat the radio link confi guration process.
If you have selected the timer comfort function, you
can also set the timer in comfort mode (default is
set to 3 hrs.). Select the desired time with the "+" /
"-" keys, then confi rm the selection by pressing and
holding on the "OK" key.
You can exit the confi guration process at any time
by pressing and holding on the cancellation key.
For "Radio link elimination" and "reset ", see § 4.
Standard operation
In standard operation, the screen will be switched off
to conserve battery power (it is possible to change
this setting and leave the screen continuously on,
please refer to chapter "EK760 setting"). Pressing
on the "+" / "-" buttons briefl y will display the
measured temperature, and the 6th and 7th icons
(indicated at the "Overview of the Thermostat") will
indicate if the thermostat is in comfort
mode or
in
Night setpoint
mode.
From this screen, several options are available:
1. Consultation of the existing setpoint
temperature
You can check the current temperature setpoint by
pressing on the "+" or "-" keys briefl y. The current
temperature setting (Comfort or
Night setpoint
) will
fl ash and display for 10 sec, before the measured
temperature will be displayed again.
2
.
Ongoing setpoint temperature bypass
To temporarily change the current temperature
setpoint, press on the "+" or "-" key to increase
or reduce the temperature.
The setpoint temperature will blink, and automatically
validated after 10 sec or by pressing and holding
on the "OK" key. This bypass is valid until the
next mode adjustment (next step of the heating
schedule initiated by the house automation
controller TKP100A, for example).
The icon "
ongoing temperature bypass indicator"
will be displayed on the screen to indicate that the
bypass is in progress.
To cancel this bypass: press and hold on the
"return" key, and the icon "
ongoing temperature
bypass indicator" will disappear.
3
.
Product safety locking
To avoid unintentional activation, you can lock the
EK760. For this, press and hold the + /- keys at the
same time
keys simultaneously until the " " icon
appears on the screen. To deactivate the function,
repeat the process until the " " icon disappears.
4
.
EK760 settings
To access the product settings, it is necessary to
press on the "+" and "–" keys to enter the menu,
then navigate in the menu by pressing on the "+"
and "-" buttons briefl y. To enter one of the settings,
press and hold on the "OK" key. To exit a setting or
the menu, press and hold on the "Return" key.
Different settings are accessible:
• "Mode" : Change of heating mode
There are 2 heating modes on the product (comfort
and economy). It is possible to change the heating
mode by selecting the "
Mode
" setting. By pressing
on the "+" button briefl y, you can select "
Conf
"
(for Comfort mode) or "
Night
" (for night setpoint
mode). The selection can be confi rmed by pressing
and holding on the "OK" key.
• "Priority" : Forcing of the thermostat heatin mode
The priority mode allows you to maintain a
constant temperature in your house in comfort or
economy mode, but does not take into account
some programming profi les (for example, profi les
available on the house automation controller
TKP100A). To select the "Priority" mode in the
menu, confi rm selection by pressing and holding
on the "OK" key and select the desired mode with
the "+" / "-" keys:
•
Comf.
: To enter comfort mode
•
Night
: To enter night setpoint mode
•
DIS
: to disable the priority mode
Confi rm your selection by pressing and holding on
the "OK" key.
• "Temperatures" : Adjustment of the temperature
setpoint for the different heating modes
2
3
4
5 6
7
8
9
A
1
Z
Heating
Function on the EK760 display
Comfort
Night setpoint
Heating pause
Heating pause*
S1
Scenario 1
S2
Scenario 2
Temporary
Comfort / Night setpoint
Priority
Priority
Window*
Room temperature*
del
Delete
/
Specifi cations
Power supply: 4 AA LR6 1.5V batteries
Battery lifespan: 4 years
Setting range
• Comfort mode temperature: +5 °C to +30 °C
• Night setpoint mode temperature: +5 °C to +30 °C
Room temperature display range: 0 °C to +40 °C
Operating temperature: +0 °C to +50 °C
Storage temperature: -20 °C to +70 °C
Ball pressure test temperature 75 °C
Humidity: max 93% at 40 °C
IP: 20
IK: 04
Degree of pollution: 2
Action type: 1.L
Software structure: class A
Dimensions (l x h x d): 74.7 x 48 x 63.1 mm
Emission frequency: 868-870MHz/25mW
Transmitter duty cycle: 0.1
Receiver category: 2
Typical range: >150 m in free range and 50 m (2 slabs).
The "Temperature" mode allows you to adjust the
temperature setpoint of the different heating modes
according to the range described in the table below.
Mode
Default
value
Min
Max
Interval
Comfort
20°C
5°C
30°C*
0,5°C
Night
setpoint
16°C
5°C
30°C*
0,5°C
Frost
protec-
tion
6°C
Non-confi gurable on the value
but through the house auto-
mation controller (for example,
TKP100A)
*The maximum adjustable temperature may be
limited by remote setting.
Select the "Temperature" mode in the menu and
confi rm selection by pressing and holding on the
"OK" key:
• When the "Comfort" temperature setpoint blinks,
you can change it by pressing on the "+" / "-" keys
briefl y, then confi rm selection by pressing and
holding on the "OK" key.
• When the "Night" temperature setpoint blinks,
you can change it by pressing on the "+" / "-" keys
briefl y, then confi rm selection by pressing and
holding on the "OK" key.
• "Heating pause" : Stop heating
The "Heating pause" mode allows you to turn the
heater off (for example, during summer). This helps
to increase the battery lifespan.
In this mode, only the frost protection and the anti-
scaling functions (1x per week) remains active.
Select the "Heating pause" mode in the menu and
confi rm selection by pressing and holding the "OK"
key, then select "Yes" or "No" by pressing on the "
+ " and " - " keys briefl y to activate or deactivate the
function, then subsequently confi rm by pressing
and holding on the "OK" key.
In "Heating pause" mode, the "Mode" and "Priority"
modes will not be accessible.
O
EK760 ensures anti-scaling protection of your
valve through the complete opening/closing
of the valve per week.
• "Window" : Window opening detection
The EK760 has an integrated window opening
detection function. If a window opens leading
to a drastic fall in temperature, the EK760 will
automatically close the radiator valve to save
energy. The screen will display icon "
", and
subsequently resumes its normal operation.
To confi gure this function, select the "Window"
mode in the menu and confi rm selection by
pressing and holding on the "OK" key, then select
"Yes" or "No" with a brief press on the " + " and
" - " keys to activate or deactivate the function then
confi rm your selection by pressing and holding the
"OK" key.
Now, adjust the sensitivity of the device to
temperature changes. This can be selected with a
brief press on the " + " and " - " keys ("High"= high
sensitivity, "Medium" = medium sensitivity (default
setting), "Low"= low sensitivity), then confi rm by
pressing and holding on the "OK" key.
Now, select the time (ranging from 10 minutes to
60 minutes at an interval of 5 minutes) during which
the valve must remain in frost protection mode
by pressing on the "+" and "-" keys briefl y, then
confi rm your selection by pressing and holding on
the "OK" key.
It is also possible to exit the frost protection mode
due to an open window pressing and holding on
the "enter" key.
• "Temp Offset" : Temperature calibration
This setting adjusts the measured value by the
thermostat if you are measuring a different room
temperature.
To do so, select the "Temp Offset" mode in the menu
and confi rm selection by pressing and holding on
the "OK" key. You can change the temperature
within a limit of -5 to +5°C with a short press on
the "+" / "-" keys, then confi rm your selection by
pressing and holding on the "OK" key.
The temperature offset is canceled in "Heating
pause" mode (summer period)
• "LCD Standby" : Putting the screen in standby
Putting the screen in standby helps to increase
battery lifespan. This setting provides you with the
options of permanently activating the screen or to
put it on standby after 30 sec if no key is pressed.
To do so, select the "LCD Standby" mode in the
menu and confi rm by pressing and holding on
the "OK" key. With a brief press on the "+" / "-"
keys, you can select "Yes" to activate the screen
standby function (default confi guration) or "No"
to deactivate the function (the screen remains
permanently on), then confi rm your selection by
pressing and holding on the "OK" key.
• "Installation" : Installation mode
This function enables the EK760 to enter installation
mode.
For this, select the "Installation" mode in the menu
and confi rm by pressing and holding on the "OK"
key. Once the "
INST
" fl ashes on the screen, the
motor is pushed upwards and you can install the
EK760 on the thermostatic valve. Once installed,
you can exit the installation process by pressing
and holding on the “OK” key.
• "Del radio link" : Clearing of the radio links
This function allows you to clear the existing radio
links on the EK760.
To delete radio links, select the "Del radio link"
mode in the menu and confi rm selection by
pressing and holding on the "OK" key, and a
blinking "OK" message will be displayed. You can
confi rm the clearing by pressing and holding on the
"OK" key or cancel the operation by pressing and
holding on the "Return" key.
• "Reset" : restore factory settings
This parameter resets the parameters to the factory
settings and causes the elimination of the radio
links.
To do so, select the "Reset" mode in the menu
and confi rm selection by pressing and holding on
the "OK" key, and a blinking "
OK ?
" message
will be displayed. You can confi rm the clearing by
pressing and holding on the "OK" key, or cancel the
operation by pressing and holding on the "return"
key.
• "Language" : Language confi guration
This setting allows you to select the language
used on the EK760 (English, French, German, and
Italian).
To do so, select the "
Language
" mode in the menu
and confi rm selection by pressing and holding on
the "OK" key, change the language with a brief
press on the " + " / " - " keys then confi rm your
selection by pressing and holding on the "OK" key.
• "Software version" : Version of software installed
on the product
This setting allows you to know which software
version has been installed on your EK760.
To do so, select the "Software version" mode in
the menu and confi rm selection by pressing and
holding on the "OK" key, and the software version
will be displayed. You can exit this display by
pressing and holding on the "OK" or "Return" key.
What should I do if... ?
The "Low battery" symbol is displayed: please
change the batteries (4 batteries of type AA LR6
1.5V) immediately.
The application does not detect EK760 during
confi guration: It is possible that EK760 is out of
range of the house automation controller TKP100A.
Please bring the TKP100A closer to the EK760.
The screen does not light up when the "+" or "–"
keys are pressed: Ensure that the batteries are
correctly positioned. Use only batteries of type AA
LR6 1.5V (provided with the product). If the problem
persists, replace the batteries.
I pressed the "+" or "–" keys before installing the
EK760 on the valve: Remove and reinsert the
batteries, or select the "Installation" mode in the
menu and confi rm by pressing and holding on
the "OK" key. Once a blinking "
Inst
" message is
displayed, the motor is placed in high position, you
can install the EK760 on the thermostatic valve.
Once installed, you can exit the installation process
by pressing and holding on the "OK" key.
The screen displays the code
ERR1
(adaptation
impossible):
• The EK760 is not assembled correctly. Please
repeat the assembly steps.
• The adjustment screw could have fallen. In this
case, replace the adjustment screw and then
remove the batteries briefl y to reset the device.
The motor should be positioned completely at
the top to facilitate assembly. The screen indicates
"
Inst
" ("Inst" can also be selected in the menu).
The continuous threading turns and tightens the
new adjustment screw. Proceed with the assembly
of EK760 on the thermostatic valve again.
The screen displays one of the following codes
ERR2
(Piston stroke too short) or
ERR3
(Motor
movement impossible): Remove EK760 from the
valve and press on the piston of the thermostatic
valve body. Repeat the assembly steps.
Correct Disposal of this product
(Waste Electrical & Electronic
Equipment).
Applicable in the European Union and other
European countries with separate collection
systems).
This marking shown on the product or its literature
indicates that it hould not be disposed with other
household wasted at the end of its working life. To
prevent possible harm to the environment or human
health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where
they purchased this product, or their local government
offi ce, for details of where and how they can take this
item for environmentally safe recycling.
Business users should contact their supplier and check
the terms and conditions of the purchase contract. This
product should not be mixed with other commercial
wastes of disposal.
Simplified EU Declaration of Conformity:
As per the present document, Hager Controls declares that
the radio equipment of the Radio thermostat for thermostatic
radiator valves EK760 type is compliant with the 2014/53/UE
guidelines.
The complete text of the EU Declaration of Compliance is
available at the following link
www.hagergroup.net
6LE001855B
6LE001855B
6LE001855B
