background image

69-0959

6

T8501A,B,C,D MICROELECTRONIC THERMOSTATS

Table 2. Thermostat Installer Setup Options (continued).

a

Available on select models.

Mode 02 must be set to 01 to extend fan operation.

c

 T8501D is 48

°

F.

Mode Display

(Press 

  i   

key

Factory-Setting

Other Choices  

(Press 

 or  

 key to change)

Select

to change)

Display

Description

Display

Description

Not used

13  

Degree tempera-
ture display

14

00

Temperature is
displayed in °F

01

Temperature is displayed in °C

Not used

15 thru 18  

Extended fan
operation in
heating

a,b

19  

00

No extended fan
operation after the call
for heat ends

01

Fan operation is extended  
90 seconds after the call for  
heat ends

Extended fan
operation in
cooling

a

20  

00

No extended fan
operation after the call
for cool ends

01

Fan operation is extended  
90 seconds after the call for  
cool ends

Not used

21 thru 23  

Outdoor
temperature
display

a

24

00

No outdoor temperature
is displayed

01

Outdoor temperature is displayed.
Needs a C7089B1000 Outdoor
Sensor to operate.

Not used

25 thru 32

Minimum off time
for the
compressor

33

05

5 minute minimum off
time for the compressor

00, 01,
02, 03 or
04

Minimum number of minutes  
(0 thru 5) the compressor will be
off between calls for the
compressor

Heating setpoint
range stop

a

34

90

Heating setpoint can be
set no higher than 90°F

40 thru
90

Number can be set anywhere
between 40 and 90 in 1°F
increments

Cooling setpoint
range stop

a

35

45

c

Cooling setpoint can be
set no lower than 45°F

c

45

c

 thru

99

Number can be set anywhere
between 45

c

 and 99 in 1°F

increments

System On
display

a

36

00

LCD On symbol is
displayed when system
is energized

01

Display is disabled, usually set for
01 for a zoned system

Temperature
display
adjustment

37

00

No difference in
displayed temperature
and actual room
temperature

01 thru
06

01—Display adjusts to 1°F higher

than actual room temperature

02—Display adjusts to 2°F higher

than actual room temperature

03—Display adjusts to 3°F higher

than actual room temperature

04—Display adjusts to 1°F lower

than actual room temperature

05—Display adjusts to 2°F lower

than actual room temperature

06—Display adjusts to 3°F lower

than actual room temperature

Summary of Contents for t8501A













Reviews: