background image

69-0959

7

T8501A,B,C,D MICROELECTRONIC THERMOSTATS

Table 4. Installer Self-Test Options.

Table  3. Tests Available In The Installer

Self-Test Mode.

Refer to Table 4 for the directions and results of the
specific tests.

IMPORTANT

Models with system and fan switches must set
the switches to the equipment that is being
checked for the equipment to operate.

NOTE:

Press and hold the increase 

 and decrease 

keys for three seconds to exit the self-test mode.
The self-test times out after five minutes without
any key presses.

INSTALLER SELF-TEST

Use the Installer Self-Test to check the thermostat
configurations and operation. Refer to Table 3 for a list of
the available self-tests.

To start the self-test:

NOTE:

The minimum off time for compressors is
bypassed during the Installer Self-Test.

Press and hold the increase 

 and decrease 

▼ 

keys, at

the same time, until two zeros appear. All segments of the
LCD are displayed before the two zeros appear.

(Continued)

Em HeatOffCool Auto Only

Heat Cool

OnAuto

System

Fan

Room

Outdoor

Em Ht Temporary Setting

Wait

%Humid

Aux Ht

Remote

Repl

Batt

M4844

M6792

TEST MODE
NUMBER

Test  

Number

Self-Test Description

10-19

Heating equipment can be turned on and off

30-39

Cooling equipment can be turned on and off

40-49

Fan equipment (T8501D only) can be turned
on and off.  

60-69

System key or system switch position test
(not available on T8501A)

70-79

Thermostat information including date code
and software versions are displayed

Key to

Press

Test

Mode

Number

Description

Heating Equipment Self-Test

i  

 

10

Enter heating equipment self-test. (Set system switch to HEAT on switch models.)

  

11

Heat comes on. When Installer Setup mode number 02 is 01, the system fan is also
energized.

  

10

Heat and system fan turn off.

Cooling Equipment Self-Test

i  

 

30

Change from heating to cooling equipment self-test. (Set system switch to COOL on switch
models.)

  

31

Cool and system fan come on.

  

30

Cool and system fan turn off.

Fan Equipment Self-Test (T8501D only)

i  

 

40

Change from cooling to fan equipment self-test.

  

41

Fan comes on.

  

40

Fan turns off.

Summary of Contents for t8501A













Reviews: