Honeywell MX8 Reference Manual Download Page 198 | Manualshive

Page: 198 / 318

background image

UPCE0

Note:

The UPCE0 and UPCE1 parameters are always set to match each

other. Therefore if a change is made to a parameter to either the
EPCE0 or UPCE1 Advanced Properties that same change is
automatically made to the Advanced Properties for the other
symbology.

Note:

UPCE0 and UPCE1 are enabled as the same symbology at the

scanner. Therefore, the only way for UPCE1 configuration to be used
is if UPCE0 is disabled. When UPCE0 is disabled, it is scanned by the
imager but rejected by Data Collection Wedge.

Transmit Check Character

– When enabled, transmit the check character.

Default is enabled

Transmit number System Digit – When enabled, transmit the number system
digit. Default is enabled.

Expand Version E

– When enabled, expand version E to 12-digit UPCA

format. Default is disabled.

Addenda

Read 2-Digit – When enabled, transmit the 2 digit addenda. Default is disabled.

Read 5-Digit – When enable, transmit the 5 digit addenda. Default is disabled.

Required – When enabled, only transmit bar codes with a 2 or 5 digit addenda.
Default is enabled.

Insert Separator – When enabled, insert a space between the code and
addenda. Default is disabled.

UPCE1

5-30

«
...
196
197
198
199
200
...
»

Summary of Contents for MX8































































































































































































































































































































Reviews:

No comments

Related manuals for MX8

Brand: Unitech Pages: 20

Brand: Bartec Pages: 2

Brand: Two Technologies Pages: 58

Brand: Datalogic Pages: 2

Brand: Falcon Pages: 68

Visor Visor Deluxe Handheld

Brand: Handspring Pages: 282

Brand: Unitech Pages: 50

intelliRock III

Brand: FLIR Pages: 69

Brand: Denso Pages: 36

Brand: Denso Pages: 143

Brand: Denso Pages: 159

iPAQ Pocket PC H3150

Brand: Compaq Pages: 5

iPAQ Pocket PC h3600

Brand: Compaq Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands