Honeywell MAXPRO 2.5 Installation Manual Download Page 31 | Manualshive

Page: 31 / 77

background image

MAXPRO NVR Commissioning and Installation Guide

31

3

Installing MAXPRO NVR

Overview

This chapter describes the procedures for installing the MAXPRO NVR software. Follow the
appropriate section in this chapter to complete your MAXPRO NVR software installation.

Caution:

For Honeywell’s boxed solutions, MAXPRO NVR PE, MAXPRO NVR XE
and MAXPRO NVR SE, the server and client software required is
pre-installed on the box. Hence the instructions in this chapter for Server
software fresh installation are

NOT

applicable.On the boxes, only the

installation upgrade process might apply depending on the existing
software version on the box. For client workstations, the client installation
procedure is applicable.

Before you Begin

•

Ensure that the client and server computers meet the software and hardware
requirements.

•

Ensure that the requirements mentioned in the

MAXPRO NVR Software Prerequisites

section are fulfilled.

Caution:

Before starting the installation, please ensure that Windows updates are
not updating the system, and Antivirus is not performing any live updates
in the background.

M A X P R O N V R S o f t w a r e P r e r e q u i s i t e s

Before you install Honeywell MAXPRO NVR software, please note the MAXPRO NVR Server
requirements listed in the following section.

MAXPRO NVR Server

The computer that is designated as the server must run on one of the following operating
systems.

Microsoft

®

Windows

®

7 Professional 32-bit, 64-bit

•

Service pack 1 must be installed on the NVR before installing MAXPRO NVR
software.

«
...
29
30
31
32
33
...
»

Summary of Contents for MAXPRO 2.5














































































Reviews:

No comments

Related manuals for MAXPRO 2.5

Brand: C4i Pages: 8

Brand: Cabletron Systems Pages: 21

Brand: NAIM Pages: 2

Brand: Xantrex Pages: 8

Brand: Netopia Pages: 38

DHI-NVR2104-P-4KS2

Brand: Dahua Pages: 23

Easy Tool-ID BSG TID-05-T30-00-005

Brand: Balluff Pages: 46

memonizerWORKSTATION

Brand: MEMON Pages: 2

HHM Series HHM2245SA1

Brand: TDK Pages: 2

Brand: Cervoz Pages: 22

Quadro M6000 Sync

Brand: Nvidia Pages: 8

SiliconDrive SSD-P16G(I)-3100

Brand: Silicon Systems Pages: 108

Brand: Nilox Pages: 66

Brand: Hauppauge Pages: 62

Brand: Navitar Pages: 1

FrameSaver DSL 9788 Router

Brand: Paradyne Pages: 28

Brand: Idis Pages: 18

Brand: TANDBERG Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands