manualshive.com logo in svg

Honeywell LC13-510, Manual, Page: 49 / 76

Share
Download
Honeywell LC13-510 Manual Download Page 49

Dual Node Module Service

3-13

9/95

3.3.9

3.3.9  NGI Board

SELF TST/ERR

 light does not go out.

• Ensure that NGIO board is properly installed.

• Replace NGI board.

• Replace NGIO board.

SELF TST/ERR

 light goes out, but 

PASS MOD TEST

 (green) light does not light on

one controller.

• Replace NGI board, and then the other NGI board in slot below it, if present (three-

board, redundant cable node).

• Replace K2LCN/K4LCN.

SELF TST/ERR

 light goes out, but 

PASS MOD TEST

 (green) light does not light on

all controllers.

• Replace K2LCN/K4LCN.

• Replace NGI board, then apply power.  Repeat for other NGI board, if present.  Retry

extracted boards.

BUS TRAN ERR

 light is lighted on controller, and 

DTAK TIME OUT

 is lighted on

the K2LCN/K4LCN.

• Replace NGI board, then apply power.  Repeat for other NGI board, if present.  Retry

extracted boards.

• Replace K2LCN/K4LCN.

BUS TRAN ERR

 light is lighted on a controller, and 

BGAK TIME OUT

 is lighted on

the K2LCN/K4LCN.

• Replace NGI board, then apply power.  Repeat for other NGI board, if present.  Retry

extracted boards.

• Replace K2LCN/K4LCN.

The TX (yellow) light indicates transmit activity.  If this light is not on, troubleshoot the

Plant Information Network (PIN) cables and other interfaces.

CAUTION

There is a test jumper on the front of the NGI board (near the indicator lamps described
above).  This jumper has two positions, TEST and NORMAL.  This jumper should always be in
the NORMAL position when the network is operating.  Placing this jumper in the TEST
position may disrupt operation of other nodes operating on the PIN.

Summary of Contents for LC13-510













































































Reviews:

No comments