manualshive.com logo in svg

Honeywell LC13-510, Manual, Page: 42 / 76

Share
Download
Honeywell LC13-510 Manual Download Page 42

Dual Node Module Service

3-6

9/95

3.3.2

3.3.2  Controller Boards (FDC, CNI, DHI, CLI, SIO, SPC)

SELF TST/ERR

 light does not go out.

• Ensure that I/O board is properly installed.

• Replace controller board.

• Replace I/O board.

SELF TST/ERR

 light goes out, but 

PASS MOD TEST

 (green) light does not light on

one controller.

• Replace controller board, and then board in slot below it, if present (three-board node).

• Replace K2LCN/K4LCN.

SELF TST/ERR

 light goes out, but 

PASS MOD TEST

 (green) light does not light on

all controllers.

• Replace K2LCN/K4LCN.

• Remove top controller board, then apply power.  Repeat for each controller board until

fault is cleared.  Retry extracted boards.

BUS TRAN ERR

 light is lighted on controller, and 

DTAK TIME OUT

 is lighted on

the K2LCN/K4LCN.

• Replace controller board and board in slot below it, if present, one at a time.

• Replace K2LCN/K4LCN.

BUS TRAN ERR

 light is lighted on a controller, and 

BGAK TIME OUT

 is lighted on

the K2LCN/K4LCN.

• Remove top controller board, then apply power.  Repeat for each controller board until

fault is cleared.  Retry extracted boards.

• Replace K2LCN/K4LCN.

Summary of Contents for LC13-510













































































Reviews:

No comments