background image

 

30 

Notices  

This device complies with Part 15 of the FCC Rules.  Operation is subject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.

 

 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
Part 15 of the FCC rules.  These limits are designed to provide reasonable protection against harmful 
interference in a residential installation.  This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 
radio communications.  However, there is no guarantee that interference will not occur in a particular 
installation.  If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 
one or more of the following measures: 
 

  Reorient or relocate the receiving antenna 

  Increase the separation between the equipment and receiver 

  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 

  Consult the dealer or an experienced radio/TV technician for help 

 

Notice

 

This Class B digital apparatus complies with Canadian ICES-003. 
 

Avertissement 

Cet appareil numérique de la class B est conforme à la norme NMB-003. 
 

Summary of Contents for IS220









































Reviews: