Honeywell HNDR-S4824 Page 42 User Manual Download

Page: 42 / 80

HNDR-S4824 Basic

Configuration

2004.05.31 (v 2.0)

Honeywell

5.4.3. Text

HNDR-S4824 can display and playback text data of Access Control/POS/ATM with relevant video. This

menu is to set input text information. For text recording, “COM1” part should be also set in

“System

Serial Setup” menu.

Sync Text With

To set channel to synchronize with text.

Seek Header

If a protocol is built in HNDR-S4824 like Star Finger 007, this setting is needless. Otherwise, HNDR-

S4824 can’t recognize which parameter value is input to HNDR-S4824. Namely, all information has

starting point and ending point. Header means starting point that is always inserted. So when this header

data is transmitted to HNDR-S4824, HNDR-S4824 can recognize it as starting point. Two headers can be

set maximally.

Delimiter

Because delimiter value may be different, refer to the manual of related device.

Summary of Contents for HNDR-S4824

















































































Search results

Summary of Contents for HNDR-S4824

Reviews:

Related manuals for HNDR-S4824

Brands by name

Popular brands

Honeywell HNDR-S4824, User Manual

Search results

Summary of Contents for HNDR-S4824

Reviews:

Related manuals for HNDR-S4824

Brands by name

Popular brands