manualshive.com logo in svg

Honeywell HNDR-S4824, User Manual, Page: 48 / 80

Share
Download
Honeywell HNDR-S4824 User Manual Download Page 48

HNDR-S4824 Basic 

Configuration

 

 

48 

2004.05.31 (v 2.0) 

Honeywell

5.6. Monitor 

This menu is to set display image on monitor A & monitor B.

 

 

Alarm Pop-up (sec) 

To set alarm pop-up screen. Pop-up duration time can be set between 5 and 10 seconds. If setting as 

“Keep”, pop-up screen keeps holding. In order to cancel Keep mode, press another channel button. 

 
 
 

Seq. Switching(sec) 

To set sequence time between 1 and 60 seconds. 

 
 
 

 

 

 

<Note> 

 

If channel 1 pops up and channel 2 also pops up during pop-up hold time, screen is changed to quad-

split screen and channel 1 and 2 are shown. And the pop-up hold time is extended automatically. (Up to 

8 channels) 

 
 
 

User Sequence Configuration 

To set user sequence mode. 

 
 
 

 

 

 

< Note > 

 

1. User sequence mode can be set upto #16. 

2. The example above shows 6 sequence sets; Quad split screen(1,2,3,4) 

Æ

 Single full screen(1) 

Æ

 

Quad split screen(5,6,7,8) 

Æ

 Single full screen(5) 

Æ

 Single full screen(8) 

Æ

 9-split 

screen(9,10,11,12,13,14,15,16) 

Summary of Contents for HNDR-S4824

















































































Reviews:

No comments