16
17
CARACTERÍSTICAS DE SEGURIDAD
The Honeywell HeatGenius
TM
Ceramic Heater is equipped with several devices and features for
added protection:
• A four way tip-over switch that disables the heater if it is accidently tipped in any direction. If tipped over,
the unit should be set upright and follow the OPERATION instructions.
• A high temperature safety control prevents overheating. If activated, unplug the device and wait at least
10 minutes for unit to cool. Then plug the heater back in and follow the OPERATION instructions.
• The heater is also equipped with a thermal cut-off fuse that will permanently shut down the heater should
it operate at a highter than normal temperature. If activated, the unit will need to be replaced.
• This heater was created using high quality, heat-resistant plastics and has a Cool Touch handle.
SOLUCIÓN DE PROBLEMAS
Problema
Solución
If your Honeywell HeatGenius
TM
Ceramic Heater shuts off
unexpectedly or fails to
operate, one of your heater
safety features may have
been activated to prevent
overheating.
• Asegúrese que esté conectado y que el tomacorriente
esté funcionando.
• Verifique si hay obstrucciones. Si encuentra alguna, APAGUE el
calefactor ( ) y desconéctelo.
• Permita que el calefactor se enfríe completamente, luego quite
la obstrucción. Espere por lo menos 10 minutos, luego vuelva a
conectar el calefactor y siga las instrucciones de OPERACIÓN.
It is recommended that the Honeywell HeatGenius
TM
Ceramic Heater be cleaned at least once a month and
before off-season storage.
• Turn Off ( ) and unplug heater. Allow unit to cool.
• Use a dry cloth only to clean the external surfaces of the heater.
DO NOT USE WATER, WAXES, POLISHES
OR ANY CHEMICAL SOLUTION.
• Before storing, clean the Ceramic Heater using the above-mentioned steps. Wrap the cord around the unit.
Place in its original box and store it in a cool, dry place.
• This heater does not disassemble.
• Presione y mantenga presionado los Botones de Control del Termostato (
) durante tres segundos para
cambiar entre Fahrenheit y Celsius y viceversa.
LIMPIEZA Y ALMACENAJE
FAHRENHEIT A CELSIUS
Modelo(s)
Dimensión de la Unidad
Amperes
Voltaje de la
Unidad
Watts Max
BTUs
Max
HCE840B /
HCE840C
22.2 cm L x 17cm A x 32.5cm
A, 1.45 kg
12.5
120V, 60Hz
1575
5118
ESPECIFICACIONES DEL PRODUCTO
6 HEAT SETTINGS THAT GIVE YOU CONTROL OF YOUR COMFORT
Fig. 3
Fig. 2
Low Heat
& "White
Noise"
Setting
2 Hour
Auto-off
Timer with
30 Minute
Phased
Intervals
6 Ways to Heat the Space You are In
- Once your heater is ON, use the control buttons on the bottom to
select the desired heat setting for your needs. Your heater will start on the Constant Hi Room heat setting
each time you turn the heater on. Here is a handy reference to help select the heat option that best suits
your desired comfort level:
FLOOR AREA – (LOW HEAT)
This setting uses the lower level heating element only to provide a comfortable, gentle heat to warm up the
floor area in front of the heater.
PERSONAL – (MODERATE HEAT)
This setting uses a moderate heat level to warm you personally wherever you may be relaxing (reading,
watching TV, etc.). The LO option ( ) provides a soothing heat level, while the HI option ( ) slightly
increases heat output, allowing you to adjust to your desired comfort level.
ROOM – (MODERATE-HIGH HEAT)
Best for whole room heating, use this setting to bring warmth to cooler, drafty rooms. The LO option
provides a moderate heat level, while the HI option uses maximum heat output to create a warmer
environment.
THERMOSTAT – (MODERATE-HIGH HEAT)
To set the Thermostat, press the Thermostat Control Buttons (
) to choose your Desired
Temperature. The Desired Temperature will flash five times and then the Current Temperature in the room
will display as a steady number. The Thermostat can operate on either HI or LO heat levels to achieve
Desired Temperature by pressing the (
) button under Room.
NOTE:
If the Current Temperature is higher than your Desired Temperature, the heater will go into cool down
mode and then shut-off until the room temperature falls below this setting or until the Desired Temperature
is changed.
HEATPHASE™ TIMER
The new HeatPhase Timer is an auto-off feature that gradually transitions the room temperature from
warmer to cooler. The timer starts at high heat and steps down 4 different heat levels until it shuts off - over
a 2 hour period. This feature is ideal for setting a comfortable, relaxing environment. (Fig. 2) The timer can
also be toggled to start at whichever level desired.
QUIET MODE
The new Quiet Mode features uses a low heat setting and fan speed to produce a gentle "white noise" and
soothing warmth. (Fig. 3)
