Honeywell Genesis 7580G User Manual Download

Page: 37 / 202

2 - 17

Turbo Mode:

The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode.

Default = Off.

Numeric Keypad Mode:

Sends numeric characters as if entered from a numeric keypad.

Default = Off.

Automatic Direct Connect Mode:

This selection can be used if you have an IBM AT style terminal and the system is dropping

characters.

Default = Off.

DOS Mode C X Mode On

Windows Mode Prefix/Suffix Off

Turbo Mode On

* Turbo Mode Off

Numeric Keypad Mode On

* Numeric Keypad Mode Off

Automatic Direct Connect Mode

* Automatic Direct Connect

Mode Off

Summary of Contents for Genesis 7580G











































































































































































































Search results

Summary of Contents for Genesis 7580G

Reviews:

Related manuals for Genesis 7580G

Brands by name

Popular brands

Honeywell Genesis 7580G, User Manual

Search results

Summary of Contents for Genesis 7580G

Reviews:

Related manuals for Genesis 7580G

Brands by name

Popular brands