manualshive.com logo in svg

Honeywell FlexLine SmartServo 954, Installation Manual, Page: 10 / 45

Share
Download
Honeywell FlexLine SmartServo 954 Installation Manual Download Page 10

 

 

 

Part No: 4417341 Revision 10   

 

 

Installation Manual                                                                  10 
954 SmartServo FlexLine  

 

 

                       

 

 

 

Safety Instructions 

 

2.3.1. Safety Instructions 

See  the  safety  instructions  shipped  with  the  device  for  installation, commissioning, 
operation, and maintenance. 

 

2.3.2. EC Declaration of Conformity (for EU) 

Refer to the EC declaration of conformity shipped with the device. 

 

2.3.3. Control Drawings for FM & CSA 

Refer to the control drawings shipped with the device. 

 

2.3.4. Users 

The mechanical and electrical installation must be  carried out  only  by trained personnel 
with  knowledge  of  the  requirements  for  installation  of  explosion-proof  equipment  in 
hazardous areas.

 

The entire installation procedure must be carried out in accordance with national, local, and 
company regulations.

 

The  entire  electrical  installation  shall  be  carried  out  in  accordance  with  the  national 
requirements for electrical equipment to be installed in hazardous areas. 

NOTE:  

See EN IEC 60079-14 or NEC (NFPA70).  

 

 

2.3.5. Additional Information 

If you require additional information, contact Honeywell or its representative. 

 

2.3.6. Environmental Conditions 

Observe the environmental conditions for the temperature and the pressure. 

Ambient Operating Temperature Range from -40°C (-40°F) up to +65°C (149°F). 

 

 

 

Summary of Contents for FlexLine SmartServo 954














































Reviews:

No comments