manualshive.com logo in svg

Honeywell DirectLine DL424, User Manual, Page: 8 / 38

Share
Download
Honeywell DirectLine DL424 User Manual Download Page 8

Introduction 

1.2 Electronics Module 

The electronics module is loop-powered by 16-42 Vdc and will modulate its supply 
current from 4 mA to 20 mA, depending upon the DO value that is measured by the 
probe. The transmitted loop current is compensated for process temperature. 

A 4-20 mA output connection is provided via a 6m cordset or a customer supplied 
cable used in combination with a field wiring connector. 

The DirectLine ® electronic module for dissolved oxygen measurements is available 
in two configurations:   

 

ppm (DL424) and ppb (DL425).   

 

 

Figure 1-2   Electronics Module 

 

 

1.3 Operator Interface 

The DirectLine® Sensor operator interface consists of three pushbuttons and one 
4-digit, 7-segment LCD display with 3 decimal points, plus (+), and minus (–) signs. 
It is responsible for the display of measured values and configuration of parameter 
values. 

 

2 

DirectLine® DL424/425 Sensor Module User Manual 

9/11 

Summary of Contents for DirectLine DL424







































Reviews:

No comments