manualshive.com logo in svg

Honeywell DirectLine DL424, User Manual, Page: 28 / 38

Share
Download
Honeywell DirectLine DL424 User Manual Download Page 28

Operation 

5. Operation 

5.1 Displays 

Overview 

The DirectLine® DL424/425

 

displays the On-line DO Concentration value and the On-

line Temperature.  The table below describes these parameters. 

Table 5-1   Online Parameter Descriptions 

Parameter 

Description 

Online DO 

D424 Range: ppm = 0.00 to 20.00 
D425 Range: ppb = 0 to 200 

Online 
Temperature 

Measured temperature expressed with fixed tenths decimal 
precision. 
Temperature displayed in 

C or 

F 

Range:  2.0 to 60.0 

C 

 

35.6 to 140.0 

F 

 

The default display and home position is the 

Online DO

 display. It appears when: 

  The unit is powered up after the nPrb option is selected 

  No button presses for 60 seconds 

  The Mode button has been pressed during Air or Sample calibration  

  The Mode button has been pressed momentarily during a configuration edit 

The DO measurement and display is updated at a rate of 500 ms. 

 

In the DL425, when the DO value is outside the 200ppb range, the live DO value will 
alternately flash ppm and the current reading.  The output will be in burnout as the 
reading is outside the operating range. 

22 

DirectLine® DL424/425 Sensor Module User Manual 

9/11 

Summary of Contents for DirectLine DL424







































Reviews:

No comments