manualshive.com logo in svg

Honeywell 50081314, Quick Start Manual, Page: 5 / 13

Share
Download
Honeywell 50081314 Quick Start Manual Download Page 5

Honeywell Sensing and Control     

5

Limitless™ WLS Series 

Single Switch Adapter

ISSUE 1

  

 

50081314

Figure 4. WLS Single Switch Adapter BT3 & BT4 Switch 
Term and Wires

Figure 5. WLS Single Switch Adapter BT3 & BT4 WECO 
Connector Term and Wires

1.3 

Battery Connection Procedure

m

 WARNING

RISK OF DEATH OR SERIOUS INJURY FROM EXPLOSION OR FIRE

Connection and disconnection of the batteries should only be performed in a non-hazardous area. The batteries used in this 

device may present a risk of fire or chemical burn if mistreated. Do not recharge, disassemble, heat above 100 °C [212 °F], or 

incinerate.

Failure to comply with these instructions could result in death or serious injury.

m

 WARNING

RISK OF DEATH OR SERIOUS INJURY FROM EXPLOSION OR FIRE

If WLS Single Switch Adapter is to be returned to Honeywell for any reason, the battery MUST be removed prior to shipping. 

Dispose of used batteries promptly per local regulations or the battery manufacturer’s recommendations. Keep away from 

children. Do not disassemble and do not dispose of in fire.

Failure to comply with these instructions could result in death or serious injury.

, 

ATTENTION

RISK OF DEATH OR SERIOUS INJURY FROM EXPLOSION OR FIRE

Use only the following 3.6 V lithium thionyl chloride (Li-SOCl2) battery (non-rechargeable), size 2/3 AA. No other batteries are 

approved for use in the WLS Single Switch Adapter.

•   Uniwell, DEV-10-0009
•   Green Energy, ER14335M
•   Honeywell, WBT1

Summary of Contents for 50081314














Reviews:

No comments