background image

HZ221 TrueZONE

 

5 69-2200—03

The HZ221 TrueZONE panel contains an LED display that communicates system and zone status. The LEDs indi-

cate the following information.

OPERATION

HZ221

HEAT

COOL

FAN

PURGE

ZONE 1

ZONE 2

   EM HEAT

M28239A

LED display.

Table 5. LED Operation.

LED

Description

HEAT

Solid when in heat. 

Blinking when DATS temperature exceeds 120°F 
(49°C) and calling for heat pump only. 

Blinking when DATS temperature exceeds 160°F 
(71°C) and calling for heat pump and auxiliary 
heat. At 150°F (66°C), auxiliary heat is disabled.

COOL

Solid when in cool. Blinking when 45°F (7°C) 

DATS low limit mode has been reached.

FAN

Solid when in operation.

PURGE

Solid when in purge (lasts 2 minutes at power-up 

and after a call for heat or cool). Blinking when 

the DATS sensor has failed, or the wires are short-

ed or open. Will blink for 3 minutes at power-up if 

DATS is not present.

ZONE 1, 2

Solid green when open or opening.
Solid red when closed or closing.
Blinking amber when there is a damper or ther-

mostat short circuit (circuit breaker trip).

EM HEAT

Solid when in Em Heat mode.

HZ221

2 Zones, 2H/1C

LED Status

Heat LED 

Heating Mode

Flashing Heat LED 

High Limit

Cool LED 

Cooling Mode

Flashing Cool LED 

Low Limit

Purge LED 

Purge Mode

Flashing Purge LED 

Sensor Failure

Fan LED 

Fan On

Zone LEDs 

Green - Open

 

Red - Closed

 

Flashing - Short

Zone Names

Zone 1 _______________________

Zone 2 _______________________

Technical Support: 1-800-828-8367

customer.resideo.com

Patents Pending

                                    50031314-001 Rev. A

M28240A

Em Heat LED                 Em Heat Mode

Much of this information is also listed on the label on 

the inside of the HZ221 cover.

When the zone panel cover is off, the EMERGENCY HEAT/PURGE OVERRIDE but-

ton is visible.
When the panel is in Purge (at startup or after a call for heat/cool), pressing this 

button stops the Purge, which saves time during installation or troubleshooting.
All other times, pressing the button puts the zone panel into Em Heat mode so that 

all calls for heat are handled by the auxiliary heat.

M24741A

M1

M4

M6

R

C

W

Y

G

M1

M4

M6

R

C

W

Y

G

M1

M4

M6

R

C

W

Y

G

Rh

Rc

W

Y

G

HZ311

HEAT

COOL

FAN

PURGE

ZONE 1

ZONE 2

ZONE 3

ZONE 

1

DAMPER

THERMOS

TA

T

R

C

DATS

DATS

EQUIPMEN

T

POWER

SENSOR

ZONE 

3

DAMPER

THERMOS

TA

T

ZONE 

2

DAMPER

THERMOST

AT

PURGE OVERRIDE

EMERGENCY HEAT

Summary of Contents for HZ221 TrueZONE









Reviews: