Honda VFR800FE 2014 Owner'S Manual Download Page 38

Page: 38 / 141

n Gu

TCS (Traction Control System) indicator

• Comes on when the ignition switch is turned on.

Goes off when your speed reaches approximately
10 km/h (6 mph) to indicate TCS is ready to work.

• Blinks when TCS is operating.

If it comes on while riding:

(P98)

Right turn signal indicator

ABS (Anti-lock Brake System) indicator

Comes on when the ignition switch is turned on.
Goes off when your speed reaches
approximately 10 km/h (6 mph).

If it comes on while riding:

(P97)

HISS indicator

(P117)

• Comes on briefly when the ignition

switch is turned on with the engine stop
switch in the

(Run) position.

Goes off if the ignition key has the
correct coding.

• Flashes every 2 seconds for 24 hours

when the ignition switch is turned off.

TCS (Traction Control

System) OFF indicator

Comes on when the TCS is
turned off.

High coolant temperature

indicator

Comes on briefly when the ignition
switch is turned on.

If it comes on while riding:

(P95)

14 VFR800F-32MJM6000.book 35 ページ２０１４年４月４日　金曜日　午後６時３８分

Summary of Contents for VFR800FE 2014














































































































































Search results

Summary of Contents for VFR800FE 2014

Reviews:

Related manuals for VFR800FE 2014

Brands by name

Popular brands

Honda VFR800FE 2014, Owner'S Manual

Search results

Summary of Contents for VFR800FE 2014

Reviews:

Related manuals for VFR800FE 2014

Brands by name

Popular brands