Honda VFR800FE 2014 Owner'S Manual Download Page 104

Page: 104 / 141

Tyre Puncture

Removing Wheels

101

continued

ou
bles

hoo

ting

When removing and installing the wheel, be
careful not to damage the wheel speed
sensor and pulser ring.

❙

Front Wheel

Removal

Park your motorcycle on its centre stand
on a firm, level surface.

Cover both sides of the front wheel and
brake caliper with protective tape or
cloth.

Remove the wheel speed sensor by
removing the bolts.

On the right side, remove the mounting
bolts and remove the brake caliper.

On the left side, remove the mounting
bolts and remove the brake caliper.

Support the brake caliper so that it
doesn’t hang from the brake hose. Do
not twist the brake hose.

Avoid getting grease, oil, or dirt on
the disc or pad surfaces.

Do not pull the brake lever while the
brake caliper is removed.

Take care to prevent the brake caliper
from scratching the wheel during
removal.

Mounting bolts

Brake caliper

Bolts

Wheel speed sensor

Tape or cloth

14 VFR800F-32MJM6000.book 101 ページ２０１４年４月４日　金曜日　午後６時３８分

Summary of Contents for VFR800FE 2014














































































































































Search results

Summary of Contents for VFR800FE 2014

Reviews:

Related manuals for VFR800FE 2014

Brands by name

Popular brands

Honda VFR800FE 2014, Owner'S Manual

Search results

Summary of Contents for VFR800FE 2014

Reviews:

Related manuals for VFR800FE 2014

Brands by name

Popular brands