Honda HRJ216 Owner'S Manual Download Page 52 | Manualshive

Page: 52 / 70

background image

2. Use a spark plug wrench to remove the spark plug.

3. Inspect the plug; replace it if the electrode is worn, or if the insulator is

cracked or chipped. Clean plug completely if you are going to reuse it.

4. Measure the spark plug gap with a suitable gauge. The gap should be

0.7 - 0.8 mm. Correct the gap, if necessary, by bending the side elec-
trode.

5. Install the spark plug carefully by hand, to avoid cross-threading.

6. After the spark plug seats, tighten with a spark plug wrench to compress

the washer.

If reinstalling the old spark plug, tighten 1/8 to 1/4 turn after the spark
plug seats.

If installing a new spark plug, tighten 1/2 turn after the spark plug seats.

• A loose spark plug can overheat and damage the engine.

• Overtightening the spark plug can damage the threads in the cylinder

head.

7. Install the spark plug cap on the spark plug.

NOTICE

51

0.7 - 0.8 mm

SPARK PLUG WRENCH

SIDE ELECTRODE

SEALING
WASHER

INSULATOR

«
...
50
51
52
53
54
...
»

Summary of Contents for HRJ216







































































Reviews:

No comments

Related manuals for HRJ216

Brand: Yard-Man Pages: 11

Brand: McCulloch Pages: 10

911394 - Pro 21SCH

Brand: Gravely Pages: 23

Brand: Honda Pages: 24

Brand: Viking Pages: 284

Brand: MTD Pages: 60

147W834H401 Series

Brand: Yard-Man Pages: 40

APACHE 1275 ZSL

Brand: Garland Pages: 184

Brand: Cub Cadet Pages: 40

Brand: Craftsman Pages: 48

Brand: Craftsman Pages: 48

Brand: Craftsman Pages: 20

Brand: Craftsman Pages: 21

Brand: Craftsman Pages: 20

Brand: Craftsman Pages: 48

Brand: Craftsman Pages: 20

Brand: Craftsman Pages: 21

37115 - Rear Bag Push Lawn Mower

Brand: Craftsman Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands