Honda HRJ216 Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 70

background image

20

Fuel

Refuel in a well-ventilated area before starting the engine. If the engine has
been running, allow it to cool. See page 52 for fuel recommendations.

Remove the fuel filler cap and check
the fuel level. Refill the tank if the
fuel level is low. Refuel carefully to
avoid spilling fuel. Do not overfill;
there should be no fuel over the limit
mark. After refueling, tighten the fuel
filler cap securely.

Gasoline is highly flammable and explosive.

You can be burned or seriously injured when handling fuel.

•

Stop the engine and keep heat, sparks, and flame away.

•

Handle fuel only outdoors.

•

Wipe up spills immediately.

Never refuel the mower inside a building where gasoline fumes may reach
flames or sparks. Keep gasoline away from appliance pilot lights, barbe-
cues, electric appliances, power tools, etc.

Spilled fuel is not only a fire hazard, it causes environmental damage. Wipe
up spills immediately.

Fuel can damage paint and plastic. Be careful not to spill fuel when filling
your fuel tank. Damage caused by spilled fuel is not covered under warran-
ty.

NOTICE

FUEL FILLER CAP

UPPER LIMIT

«
...
19
20
21
22
23
...
»

Summary of Contents for HRJ216







































































Reviews:

No comments

Related manuals for HRJ216

Brand: Yard Machines Pages: 16

Brand: Yazoo/Kees Pages: 42

Brand: LawnMaster Pages: 31

Brand: Yazoo/Kees Pages: 46

Brand: Poulan Pro Pages: 48

Brand: Toro Pages: 28

Patriot FDR1660

Brand: Land Pride Pages: 2

Brand: True-Surface Pages: 88

Brand: Scag Power Equipment Pages: 41

Brand: Poulan Pro Pages: 29

Brand: Toro Pages: 56

Brand: Poulan Pro Pages: 4

Brand: KUHN Pages: 48

Brand: Craftsman Pages: 34

Brand: Craftsman Pages: 34

Brand: Craftsman Pages: 56

Brand: Craftsman Pages: 56

Brand: Craftsman Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands