Honda HRJ216 Owner'S Manual Download Page 17 | Manualshive

Page: 17 / 70

background image

CHECK YOUR MOWER

Blade

Before each use, check the cutter blade for damage or excessive wear.

To avoid severe personal injury, disconnect the spark plug cap to pre-
vent accidental starting, and wear heavy gloves to protect your hands
from the cutter blade.

1. Stop the engine and turn the fuel valve to the OFF position.

2. Disconnect the spark plug cap from the spark plug (see page 50).

3. Remove the grass bag (if installed).

4. Tilt the mower to the right, so the carburetor side is up. This will help to

prevent fuel leakage and hard starting.

16

OFF

FUEL VALVE

«
...
15
16
17
18
19
...
»

Summary of Contents for HRJ216







































































Reviews:

No comments

Related manuals for HRJ216

Brand: Dixon Pages: 8

Brand: LawnBoss Pages: 34

Brand: Racing Pages: 21

Brand: Texas Pages: 60

Brand: Hayter Pages: 40

Brand: Toro Pages: 72

Brand: Lastec Pages: 68

NZMX30614KH, NZMX32734BV

Brand: Snapper Pages: 13

Brand: Stiga Pages: 30

Brand: MTD Pages: 19

Brand: Troy-Bilt Pages: 48

Brand: Cub Cadet Pages: 2

Brand: Makita Pages: 116

Brand: Bushranger Pages: 20

Brand: McCulloch Pages: 12

Brand: McCulloch Pages: 24

Brand: McCulloch Pages: 8

Brand: McCulloch Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands