background image

Current customer service contact information: 

 

Servicing dealership personnel are trained professionals. They should be able to answer any question you may 
have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the 
dealership's management. The Service Manager, General Manager, or Owner can help. Almost all problems 
are solved in this way.  

United States, Puerto Rico, and U.S. Virgin Islands: 

If you are dissatisfied with the decision made by the dealership's management, contact the Honda Regional 
Engine Distributor for your area (

www.honda-engines.com/dea.htm

). 

If you are still dissatisfied after speaking with the Regional Engine Distributor, you may contact the Honda 
Office as shown. 

American Honda Motor Co., Inc. 
Power Equipment Division 
Customer Relations Office 
4900 Marconi Drive 
Alpharetta, GA 30005-8847 

Or telephone: (770) 497-6400 M-F, 8:30 am - 7:00 pm EST 

When you write or call, please provide the following information: 

  Equipment manufacturer's name and model number that the engine is mounted on 

  Engine model, serial number, and type 

  Name of the dealer who sold the engine to you 

  Name, address, and contact person of the dealer who services your engine 

  Date of purchase 

  Your name, address, and telephone number 

  A detailed description of the problem 

 

Summary of Contents for GD320






































Reviews: