background image

2

PRODUCT SPECIFICATIONS

SPECIFICATIONS

SPECIFICATIONS

Showerhead Max. Flow Rate: 1.8 GPM (6.8 LPM) at 80 PSI

Polished chrome finish

ASME A112.18.1/CSA B125

Washerless cartridges

ASSEMBLY INSTRUCTIONS

1

.  Turn off water at the supply valve 

under the sink or at the main water 

supply, disconnect the supply line, 

and remove old faucet.
Verify that the hole sizes and positions 

in the wall are correct.
IMPORTANT: Complete valve 

replacement is required for this tub/

shower unit. An access hole must be 

cut with enough room to install the 

new tub/shower valves inside the wall. 

Professional installation is recom-

mended.
CAUTION: Do not use PEX tubing 

for pipe from the valve to the tub 

spout.

1

4.

Installing the supply 

connections:

Wrap thread sealant tape around 

the valve body (H) threads in a 

clockwise direction, as shown. 

Thread the waterline (4.

1

) to  

the valve body (H), and tighten 

with a wrench.
NOTE: Be sure to position the 

valve body (H) corretly in the wall, 

with the markings “UP” facing 

upward. Hot water supply lines go 

into the H inlet and cold water 

supply lines go into the C inlet.

Cold

Hot

4.1

H

4

2. 

NOTE: The shower outlet hose 

should be 

1

-

1

/4 in. in diameter. 

For the cold water inlet (the right 

side) and the hot water inlet (the left 

side), cut or leave a 

1

-3/8 in. to 2 in. 

diameter hole (recomended size is 

1

-3/4 in.). The center to center 

distance between the cold and hot 

water inlets should be 8 in.

1-3/8 in. ~ 2 in.

1-3/8 in. ~ 2 in.

8 in. Min.

        48 in.

Tub & Shower

        30 in.

Tub & Shower

8 in.

2

5.

Installing the tub and shower 

outlet connections:

Wrap thread sealant tape around 

the pipe threads in a clockwise 

direction, as shown. Connect the 

shower (5.

1

) (not included) and 

tube outlet pipes (5.2) (not 

included) to the valve body (H). 

Connect the pipe elbows (5.3) 

(not included) to the ends of both 

pipes, and tighten with a wrench.

 

NOTE:

 

Do not use PEX or 

CPVC between the valve and 

spout.

Shower

5.3

5.1

H

5.2

Tub

5

3.

IMPORTANT: Do not disassemble 

the the cartridges during normal 

installation.
When reinstalling the cartridge, be 

sure to insert with the cartridge slot 

(3.

1

 & 3.2) pointed outward as 

shown. This is necessary for proper 

operation of the valve.

3.1

3.2

3

6.

Flushing the water outlets 

and checking for leaks:
NOTE: 
Turn water supply back 

on.
Turn on the hot and cold water 

supply line, allowing water to flow 

from the tub spout outlet (6.

1

until all debris is cleared from  

the line. 
Check all connections for leaks.

6

6.1

HomewerksWW.com

Summary of Contents for AQUA VISTA 10SHO1H-CH-AV

Page 1: ...y of product make sure all parts are present Compare parts with package and hardware contents list If any part is missing or damaged do not attempt to assemble the product Contact customer service for replacement parts Estimated Assembly Time 30 minutes Tools required for assembly not included adjustable wrench thread sealant tape strap wrench Phillips head screwdriver silicone Installation may va...

Page 2: ... The shower outlet hose should be 1 1 4 in in diameter For the cold water inlet the right side and the hot water inlet the left side cut or leave a 1 3 8 in to 2 in diameter hole recomended size is 1 3 4 in The center to center distance between the cold and hot water inlets should be 8 in 1 3 8 in 2 in 1 3 8 in 2 in 8 in Min 48 in Tub Shower 30 in Tub Shower 8 in 2 5 Installingthetubandshower outl...

Page 3: ...5 16 in to 4 3 32 in from the finished wall to the lower pipe elbow 8 1 not included Tighten the elbows 8 1 and tub spout outlet pipe connec tions 8 2 with a strap wrench not included Thread the spout F onto the tub spout outlet pipe connec tion 8 2 in a clockwise direction until the tub spout F becomes flush with the finished wall Use a strap wrench to tighten the tub spout F F 8 1 8 2 Wall 3 15 ...

Page 4: ...lting from the use of abrasive or chemical cleaners SHALLVOID THIS WARRANTY This warranty is not applicable to any products or parts of products where damage is caused by use of non genuine parts is due to installation error product misuse negligence or faulty maintenance or where the product is not installed according to local building codes This warranty excludes labor charges or damage incurred...

Reviews: