holzkraft 5966770, Translation From The Original Instruction Manual, Page: 20 / 56

page: 20
GB
• Provide good lighting.
• Do not saw near flammable liquids or gases.
• Wear suitable work clothes! Loose garments or jewelry may become caught up in the rotating saw blade.
• Non-slip shoes are recommended when working outdoors.
• Wear a hair net if you have long hair.
• Avoid abnormal working postures.
• Operators must be at least 16 years of age.
• Keep children away from the machine when the motor is running.
• Keep your workplace clean of wood scrap and any unnecessary objects.
• An untidy work area invites accidents.
• Do not allow other persons, especially children, to touch the tool. Keep them out of your work area.
• Persons working on the machine should not be distracted.
• Note the direction of rotation of the motor and saw blade. Use only blades whose permissible maximum speed is not lower than
the maximum spindle speed of the circular saw and of the material to be cut.
• After you have switched off the motor, never slow down the saw blade by applying pressure to its side.
• Only fit blades which are well sharpened and have no cracks or deformations.
• Only use saw blades that are recommended by the manufacturer, comply with EN 847-1.
• Faulty saw blades must be replaced immediately.
• Never use saw blades which do not comply with the data specified in this manual.
• Never dismantle the machines safety devices or render them inoperative.
• If the table insert is worn, replace it.
• Always stand to the side of the saw blade when working with the saw.
• Never load the machine so much that it cuts out.
• Make sure that off-cuts do not catch on the saw blade crown.
• Never remove loose splinters, chips or jammed pieces of wood when the saw blade is running.
• To rectify faults or remove jammed pieces of wood, always switch off the machine first. - Pull out the mains plug or remove the
tractor ignition key -
• If the sawing gap is worn, replace the table insert. Turn off the machine and pull out the mains plug or remove the tractor ignition
key.
• Carry out retooling work, adjustments, measurements and cleaning jobs only when the motor is switched off. - Pull out the mains
plug or remove the tractor ignition key -
• Before switching on, make sure that all keys and wrenches have been removed from the tool.
• Switch off the motor and pull out the mains plug, or remove the tractor ignition key when leaving the workplace.
• Refit all guards and safety devices immediately after you have completed any repairs or maintenance work.
• Be sure to observe the safety information and operating and maintenance instructions issued by the manufacturer, as well as the
dimensions listed in the Technical Data.
• It is imperative to observe the accident prevention regulations in force in your area as well as all other generally recognized rules
of safety.
• Make sure you stand squarely and keep your balance at all times.
• Check the tool for damage!
• Each time before re-using the tool, carefully check that the guards or any slightly damaged parts are working as intended.
• Check that the moving parts are in good working order, that they do not jam, and that no parts are damaged. Make sure that all
parts are fitted correctly and that all other operating conditions are properly fulfilled.
• Unless otherwise stated in the operating instructions, damaged safety devices and parts must be repaired or replaced by an
authorized service center.
• This tool conforms to the applicable safety regulations. Repairs may only be performed by a specialist using original spare parts.
Otherwise accidents could occur.
• If necessary, wear suitable personal protection equipment. This could consist of:
–
Ear plugs to prevent the risk of damaging your hearing;
–
A breathing mask to avoid the risk of inhaling hazardous dust.
–
Always wear gloves when handling saw blades and rough materials. Whenever practicable, saw blades must be carried in
a container.
• The operator must be informed about the conditions that influence the generation of noise (for example saw blades designed to
reduce noise emissions, caring for blades and the machine).
• Faults on the machine or its guards, safety devices and blade must be reported to the person in charge as soon as they are dis-
covered.
• Use only the transport devices to move the machine. Never use the guards for handling and moving the machine.
• All operators must receive proper training in the use, adjustment and operation of the machine.
• Do not saw any materials that contain foreign bodies such as wires, cables or ties.
• Only use sharp saw blades.