Acessa
®
ProVu System User’s Guide
PL-01-0040
CO 20-131 Revision: C
32
Type of Specification
Specification
Ablate Temperature
The system sets the Ablate Target Temperature to 95 °C.
Power Range - Temperature
Control Mode
The system software shall limit the Ablate Power Target to the range
1 to 200 (W).
Power Control Mode
The system shall limit the Ablate Power Target to 15 W.
Coag Level
Coag Level Target is limited to the range of 1 to 20 with Level 12 as default.
Max Output Voltage
240 Vpeak into 100 Ω ablation, 350Vpeak into 300 Ω coagulation
Note that coag output voltage can go as high as 550Vpeak for high impedance
loads and momentary overshoot due to energy storage in passive filter
components.
Accessories Rated Voltage
The AcessaProVu accessories are rated for the maximum peak output voltage
as indicated. Only Acessa accessories are to be used with the Acessa ProVu
System .
Fuses
Two 7.0 Amp 250 volt fuses (in the Power Entry Module on rear panel)
Dimensions
16.5” x 18.9” x 8.0” (width x depth x height)
(41.9 cm x 48.0 cm x 20.3 cm)
Weight
30 lbs. (13.6 kg)
Controls
Main Power on/off, Standby on/off, RF on/off, System Settings
Displays
Standby Pushbutton
Orange Standby Power On LED
Target Temperature in °C
Connected accessories
Target timer in min:sec,
Average temperature of all Handpiece thermocouples in °C
Coag power level
Hottest Pad thermocouples in °C,
Expected ablation size (X & Y)
Deployment in cm
Ultrasound settings (Depth, Frequency, Gain, Focus)
Connections
Foot Pedal Port, Handpiece Port, Pad Port, Transducer Port, Transducer Sensor
Port, Field Generator Port, USB Port, Video Port (HDMI), Power Entry Module
(with internal fuses)
Protection
Class I, – Type BF Applied Part - Rated for ordinary, Continuous Operation.
Ingress of water classification: IP2X This equipment is not suitable for use in
the presence of a flammable anesthetic mixture with air, Oxygen, or Nitrous
Oxide.
Applied Parts: Handpiece, Handpiece Cable, Pads, Pads Cable, Transducer,
Transducer Sleeve, Transducer with Sensor
Transport and Storage
Temperatures: - 10
°
C to +50
°
C
Humidity: 10 to 90% non-condensing
Atmospheric Pressure: 80.1 kPA minimum
Operation
Temperatures: 10
°
C to 25
°
C
Humidity: 30% to 75%
Altitude: 2000 meters maximum
Environment
Operating room, EMC Industrial, Class A
18.2.
Guidance and Manufacturer’s Declaration –
The Acessa System is intended for use in the electromagnetic environment specified below. The customer or the end
user of the system should assure that it is used in such an environment.
Guidance and manufacturer’s declaration – Electromagnetic Emissions
Emissions test
Compliance
Electromagnetic environment - guidance
RF emissions CISPR 11
Group 1
The system uses RF energy only for its internal function. Therefore,
its RF emissions are very low
RF emissions CISPR 11
Class A
The EMISSIONS characteristics of this equipment make it suitable
for use in industrial areas and hospitals (CISPR 11 class A). If it is used
in a residential environment (for which CISPR 11 class B is normally
required) this equipment might not offer adequate protection to
radio-frequency communication services. The user might need to
Harmonic emissions
IEC 61000-3-2
Class A
Voltage fluctuations/flicker
emissions IEC 61000-3-3
Complies
