background image

 

 

User Manual 

 

Version 1.0                                                                                                                                  10 
 

equipment or service without charge at its sole discretion. Buyer assumes sole 
responsibility for any reliance on or use of such assistance and information, and the 
company makes no warranty thereon. 

Upon contact the following information is required to be provided 
Product serial number (located on rear panel instrument nameplate) 

 

Warranty card 

 

Description of issue or problem (i.e., software or hardware) 

 

Method and or operating steps you have undertaken towards resolution. 

 

Your contact details inclusive of telephone number and email address. 

For claims under the warranty please contact your local supplier. You may also send the 
instrument directly to manufacturer, enclosing the invoice copy and by giving reasons for 
the claim.  

 

IV. 

Technical Specifications.

  

 

 

 

 

Models 

10301001 

10301002 

Product Name 

Thermotita 12 

Thermotita 27 

Power

 

800W 

1000W 

Temperature Control 

Range 

RT+5

100

 

RT+5

100

 

Temperature 

Fluctuation 

 0.2

 

Tracking Alarm 

≤2

 

Mains Voltage 

120V/60Hz 

Working Room 

Dimensions               

300×240×200

 

(mm) 

500×300×200

 

(mm) 

Summary of Contents for 10301001





















Reviews: