background image

- 21 -

TRIAL RUNNING & CAPABILITY

In the Economy Mode and Hybrid Mode, if the

evaporation frosts in a cold circumstance, the system

will defrost automatically to keep effective performance

(3~10min.).  

During defrosting, fan motor will run at high speed

and e-heater will be started.   

The temperature on the display is the water

temperature in upper part of water tank (over 1/4)

which you will use, but not that of all the water.

The 6 indicators beside the water temperature on

the display are the lower part water temperature.

When the temperature is higher than 40°C, the blue

indicator will light up; if temperature is higher than

50°C, the blue and yellow indicators light up; if

temperature is higher than 60°C, the blue, yellow

and red indicators light up; in the end, when all

indicators light up, the water temperature has reached

the set point.

 

In water using, the temperature of the lower part

may decrease while the upper part still keeps a

high temperature. The system will start heating

the lower part: this is normal.  

 

When serious error happens, the system will be unable

to carry on.

Please contact the Authorized Technical Service. 

 

When error happens, the buzzer will buzz 3 minutes

every minute, ALARM indicator flashes and the display

indicates the error code and water temperature

alternatively.

Press CANCEL button for 3 seconds to stop the alarm. 

 

When the system is restarted after a long time (trial

running included), it is normal if the outlet water is

unclean.

Keep the tap on and it will be clean soon.

When common error happens, the system enters

Standby Mode and could still work, but not so efficient

as normal.

Please contact the Authorized Technical Service. 

 

Defrosting during Water-heating

(not available on these Models)

Water Temperature Display

Error Display

Restart after a Long Stop

Ambient Temperature

Mode Selection

Self-Protection Apparatuses

The system’s operation temp. is within -30°C~43°C

and below are the operation temperature for each

mode.  
Economy Mode: 5°C~43°C

Hybrid Mode: -30°C~43°C 

E-Heater Mode: -30°C~43°C 

Economy Mode: 5°C~43°C, a continuous hot water

demand below 150L(65°C); 

Hybrid Mode: -30°C~43°C, a continuous hot water

demand between 150L~200L(70°C); 

E-heater Mode: -30°C~43°C, a continuous hot water

demand between 150L~200L(70°C); 

In case of intervention of self-protection, the system

stops and self-check starts. The system restarts when

malfunction is solved. 

In the following circumstances, self-protection starts: 

1) Air inlet or outlet is obstacled; 
2) The evaporation is covered with too much dust; 
3) Incorrect power supply (exceeding the range of

207~253V). 

In case of intervention of self-protection, the buzzer

will buzz every minute, ALARM indicator flashes

and display shows error code and water temperature

alternatively.

Press CANCEL button for 3 seconds to stop the alarm.

When malfunction is solved, error code is no more

displayed. 

Different mode is designed to meet different demand

and the following are recommended selections. 

NOTE

In case of intervention of self-protection, disconnect

the appliance and restart it after malfunction has

been solved.  

Summary of Contents for HWMI 150 A





























Reviews: