background image

- 6 -

PRECAUTIONS & ACCESSORIES

PRECAUTIONS

WARNING

WARNING

WARNING

CAUTION

To prevent injury to the User or other people and

property damage, the following instructions must be

followed. Incorrect operation due to ignoring of

instructions may cause harm or damage.

The safety precautions listed below are divided in two

categories: “WARNING” and “CAUTION”.

In both cases, safety instructions are very important and

must be followed carefully.

Failure to observe a warning may result in

death or serious injury.

Failure to observe a caution may result in

injury or damage to the equipment.

The Water Heater Unit must be earthed effectively.



A creepage breaker must be installed near the power

supply.

 

Do not tear off the labels on the Units for the purpose

of warning/reminding and warranty.

 

Ask the Authorized Technical Service for installation

of Water Heater Unit.

Improper installation may result in water leakage,

electric shock or fire.
Ask the Authorized Technical Service for the repair

and maintenanance.

Improper repair and maintenance may result in water

leakage, electric shock and fire. 
In order to avoid electric shock, fire or injury, if any

abnormality is detected - such as smell of fire - turn

off the power supply and call Authorized Technical

Service for instructions. 
Never use the wire and fuse with wrong rated current.

Use of wrong wire or fuse may cause the Unit to break

down or a fire.
Do not insert fingers, rods or other objects into the

air inlet or outlet.

When the fan is rotating at high speed, it will cause

injury.  
Never use a flammable spray such as hair spray,

lacquer paint near the Unit.

It may cause a fire.
Never touch the air outlet or the horizontal blades

while the swing flaps is in operation.

Fingers may be caught or the Unit may break down. 

Never put any objects into the air inlet or outlet.

Objects touching the fan which rotates at high speed

can be dangerous.  

The appliance must be installed in accordance with

national wiring regulations.  

The appliance must not be used by children without

supervision. 
If the supply cord is damaged, it must be replaced by

the Manufacturer or by the Authorized Technical Service,

in order to avoid the hazard of electric shocks.
An all-pole disconnection device which has at least

3mm separation distance between its contacts shall

be incorporated in the fixed wiring, according to

national rules.  

If electrical appliances are disposed of in landfills

or dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging

your health and well-being.

DISPOSAL: Do not dispose this Product as unsorted

municipal waste. Collection of such waste separately

for special treatment is necessary.

Do not dispose of electrical appliances as unsorted

municipal waste: use separate collection facilities.

Please contact your local government for information

regarding systems available.

1.

Summary of Contents for HWMI 150 A





























Reviews: