background image

ASSEMBLY INSTRUCTIONS

Entire Contents © Copyright 2004

HCAZ3047 for HCAA2090  V1.0

Wingspan:

61 in [1550mm]

Wing Area:

708 sq in [45.7 dm

2

]

Weight:

7.5 - 8.5 lb [3400 - 3850g]  

Wing Loading:

24 - 28oz/sq ft [73 - 85 g/dm2]  

Length:

51.5 in [1310mm]

Radio:

Four-channel with 5 servos

Engine: 

.50 - .75 cu in [8 - 12cc] two-stroke, 

.70 - .91 cu in [11. 5 - 15cc] four-stroke

Hobbico

®

guarantees  this  kit  to  be  free  from  defects  in

both material and workmanship at the date of purchase.
This  warranty  does  not  cover  any  component  parts
damaged  by  use  or  modification. 

In  no  case  shall

Hobbico’s  liability  exceed  the  original  cost  of  the
purchased  kit.

Further,  Hobbico  reserves  the  right  to

change or modify this warranty without notice.

In that Hobbico has no control over the final assembly or
material  used  for  final  assembly,  no  liability  shall  be
assumed nor accepted for any damage resulting from the
use  by  the  user  of  the  final  user-assembled  product.  By
the  act  of  using  the  user-assembled  product,  the  user
accepts all resulting liability.

If  the  buyer  is  not  prepared  to  accept  the  liability
associated  with  the  use  of  this  product,  the  buyer  is
advised to return this kit immediately in new and unused
condition to the place of purchase.

To  make  a  warranty
claim,  send  the  defective
part  or  item  to  Hobby
Services at this address.

Include a letter stating your name, return shipping address, as
much  contact  information  as  possible  (daytime  telephone
number, fax number, e-mail address), a detailed description
of  the  problem  and  a  photocopy  of  the  purchase  receipt.
Upon receipt of the package the problem will be evaluated
as quickly as possible.

READ THIS MANUAL BEFORE

STARTING CONSTRUCTION. 

IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS

CONCERNING THE ASSEMBLY

AND USE OF THIS MODEL.

WARRANTY

Hobby Services

3002 N. Apollo Dr. Suite 1

Champaign IL  61822

USA

1610 Interstate Drive
Champaign, Illinois

(217) 398-8970 ext. 2

[email protected]

SUKHOI SU31

SUKHOI SU31

.50 - .91 

.50 - .91 

ARF

ARF

Summary of Contents for SUKHOI SU31 .50-.91 ARF

























Reviews: