HNP Mikrosysteme mzr-2542 Operating Manual Download Page 32

Page: 32 / 91

5 Optional modules

Operating manual mzr-2542 / mzr

2942

Technical data subject to change without prior notice!

Last update: January 2016

5.7

Drive with DC-Tachogenerator (optional)

The drive with DC-Tachogenerator has been designed for use in applications for
higher distance between pump and motion controller.

figure 20

Measurement with special motor

DC-Tachogenerator

EMF constant

4,3 mV/rpm

Terminal resistance

260



Operating speed



5000 rpm

Linearity, without load, between
500 and 5000 rpm

± 0,2 %



Operating temperature range

-30 … + 85°C

table 21

Technical data of the DC-Tachogenerator

Cable

Description

red Motor

black Motor

brown Tacho

white Tacho

table 22

Pin configuration of the motor cables

Warning

The micro annular gear pump mzr-4622 with special motor can operated with
the controllers S-KD-22. At the controller S-KD-22 it is to pay attention that
the jumper must set in tacho mode:

Summary of Contents for mzr-2542




























































































Search results

Summary of Contents for mzr-2542

Reviews:

Related manuals for mzr-2542

Brands by name

Popular brands

HNP Mikrosysteme mzr-2542, Operating Manual

Search results

Summary of Contents for mzr-2542

Reviews:

Related manuals for mzr-2542

Brands by name

Popular brands