HNP Mikrosysteme mzr-2542 Operating Manual Download Page 26

Page: 26 / 91

5 Optional modules

Operating manual mzr-2542 / mzr

2942

Technical data subject to change without prior notice!

Last update: January 2016

Gear reduction

Max. pump speed

(recommended max. motor speed 8000 rpm)

4.4 : 1

1818 U/min

19 : 1

421 U/min

84 : 1

95 U/min

table 9

Maximal pump speed with the gear box modules

5.2

Motor with 18 VDC voltage (optional)

The micro annular gear pumps mzr-2542 and mzr-2942 can alternatively be
driven by a Motor with 18 VDC voltage windings.

The dimensions of the micro annular gear pump do not change with the motor.

Dimensions

diameter 16

length 43

Data of capacity

Max. voltage

18 V

Max. permanent torque

4,35 mNm

output power

4,5 W

No-Load speed by 18 V

13200 U/min

No-Load speed by 8,2 V

6000 U/min

Max. permanent current

365 mA

Terminal resistor

7,44



Rotor inductance

0,28 mH

RPM speed range

100 – 6.000 U/min

Temperature range

-20 ÷ +65 °C

table 10

Technical data of the motor

figure 14

Pin configuration of the motor cable

Pin

Description

1 Motor

2 V

(5 VDC)

3 Channel

4 Channel

5 GND

6 Motor

Channel I (Index) Option

table 11

Pin configuration of the motor cable

Summary of Contents for mzr-2542




























































































Search results

Summary of Contents for mzr-2542

Reviews:

Related manuals for mzr-2542

Brands by name

Popular brands

HNP Mikrosysteme mzr-2542, Operating Manual

Search results

Summary of Contents for mzr-2542

Reviews:

Related manuals for mzr-2542

Brands by name

Popular brands