HNP Mikrosysteme mzr-2542 Operating Manual Download Page 68 | Manualshive

Page: 68 / 91

background image

10 Accessories for microfluidic systems

Operating manual mzr-2542 / mzr

-

2942

62

Technical data subject to change without prior notice!

Last update: January 2016

10

Accessories for microfluidic systems

The accessory range for the liquid delivery systems of HNP Mikrosysteme
comprises complementary equipment such as supplementary modules, hoses,
tubing, fluid connection fittings, filters and non-return valves that are best
adapted to your micro annular gear pump. We will eagerly share our long date
experience as far as component selection is concerned.

11

Non-liability clause

HNP Mikrosysteme GmbH shall not be liable for damages resulting form the
non-respect of instructions comprised in this operating manual.

It remains at the responsibility of the user to conform to all laws, rules and
regulations in force. This applies above all to the handling of aggressive,
poisonous, corrosive and other dangerous liquids as well as to the
electromagnetic compatibility (EMC).

12

Electromagnetic compatibility (EMC)

The control units S-ND and S-KG have been checked according to the
Electromagnetic Compatibility Directive 89/336/EEC.

In order to help you comply with the EMC-protection measures restrictions
concerning the S-ND control unit have been listed in the enclosed manual
"Motion Controller for DC-Motors MCDC3006".

For the control unit S-KG no further conditions must be fulfilled in order to
comply with the EMC-protection requirements.

«
...
66
67
68
69
70
...
»

Summary of Contents for mzr-2542




























































































Reviews:

No comments

Related manuals for mzr-2542

Brand: Gardena Pages: 13

Brand: WarmFlow Pages: 89

Brand: Jacuzzi Pages: 8

Brand: Bacharach Pages: 12

Bell & Gossett ecocirc XL Series

Brand: Xylem Pages: 62

Brand: Takagi Pages: 27

Brand: American Plumber Pages: 2

Brand: TradeQuip Pages: 8

Brand: TESY Pages: 176

Brand: O-SO Pure Pages: 16

HOTSPRING HSTB9

Brand: ZANSKAR Pages: 19

Brand: evoheat Pages: 17

Brand: Midea Pages: 13

Brand: Watson-Marlow Pages: 12

Brand: Kärcher Pages: 50

Brand: salmson Pages: 48

Flojet RLFP122202A

Brand: Xylem Pages: 40

Altherma EHYHBH05A Series

Brand: Daikin Pages: 264

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands