HMS Anybus IP30 Startup Manual Download Page 7

Page: 7 / 12

Installation

7 (12)

2.2.2 Digital In/Out Connectors

Anybus WLAN Access Point IP30 has 4 digital inputs and 4 digital outputs that
can be used for monitoring and controlling purposes. See the description of the
DIDO settings in the User Manual for more information.

Digital Inputs

Pin

Function

DI1

Direct input 1

DI2

Direct input 2

DI3

Direct input 3

DI4

Direct input 4

COM

Common signal ground

Digital Outputs

Pin

Function

DO1

Direct output 1

DO2

Direct output 2

DO3

Direct output 3

DO4

Direct output 4

GND

Common signal ground

2.2.3 Ethernet Connectors

Anybus WLAN Access Point IP30 has two switched Ethernet ports with RJ45
type connectors that are labeled

ETH1

and

ETH2

Pin

Function

TD+

TD-

RD+

4, 5, 7, 8

(reserved)

RD-

Anybus

WLAN Access Point IP30 Startup Guide

SP2382 EN 1.1

Summary of Contents for Anybus IP30













Search results

Summary of Contents for Anybus IP30

Reviews:

Related manuals for Anybus IP30

Brands by name

Popular brands

HMS Anybus IP30, Startup Manual

Search results

Summary of Contents for Anybus IP30

Reviews:

Related manuals for Anybus IP30

Brands by name

Popular brands