HM Electronics DX121 Operating Instructions Manual Download Page 32

Page: 32 / 39

SPEAKER STATION OPERATION

Headset Connection

If you are using a headset with the Speaker Station, plug it into the headset connector. When using a
headset, if the red light over the

SPEAKER

button is on, incoming communication can be heard through

the headset and the speaker. If the red light over the

SPEAKER

button is off, incoming communication

can only be heard through the headset.

Push-To-Talk (PTT) or Hands-Free (HF) Mode Setting

•

Be sure the WS200 power is off.

•

To set up the Speaker Station for operation in the PTT mode, press and hold the

VOLUME

down

▼

and

ISO

buttons while you press and release the

POWER

button to turn the unit on. Then release the

VOLUME

down

▼

and

ISO

buttons.

•

To set up the Speaker Station for operation in the HF mode, press and hold the

VOLUME

▲

and

ISO

buttons while you press and release the

POWER

button to turn the unit on. Then release the

VOLUME

▲

and

ISO

buttons.

NOTE:

Mode settings are saved in memory, and only need to be reset if you want to change between PTT and
HF operation. Mode settings affect both ISO and IC communication.

Headset

connector

Summary of Contents for DX121








































Search results

Summary of Contents for DX121

Reviews:

Related manuals for DX121

Brands by name

Popular brands

HM Electronics DX121, Operating Instructions Manual

Search results

Summary of Contents for DX121

Reviews:

Related manuals for DX121

Brands by name

Popular brands