Hitachi RAC-50FPA, Service Manual

Page: 11 / 101

ENGLISH
– 8 –
NAMES AND FUNCTIONS OF REMOTE CONTROLLER REMOTE CONTROLLER
ƽ
This controls the operation of the indoor unit.
The range of control is about 7 meters. If indoor lighting is
controlled electronically
, the range of controller may be shorter
.
This unit can be
fixed
on a wall using the fixture provided. Before
fixing
it, make sure the indoor unit can
be controlled from the remote controller
.
ƽ
Handle the remote controller with care. Dropping it or getting it wet may compromise its signal transmission capability
.
ƽ
After new batteries are inserted into the remote controller
, the unit will initially require approximately 10
seconds to respond to commands and operate.
ƽ
When remote controller is not in use for about 3 minutes during OFF condition, indicated by
on the
display
, the LCD will turn of
f.
ƽ
During clock setting, the LCD will turn of
f about 10 minutes later if the remote controller is not in use.
ƽ
When pressing any button, the LCD will turn on.
ƽ
The LCD will not turn of
f during
TIMER setting.
Signal T
ransmitting/Receivin
g
W
indow
Point this window towards the indoor unit when controlling it. Sensor A
temperature sensor inside the
remote controller senses ambient temperature around the remote- controller
.
Display ROOM TEMPERA
TURE setting Buttons
Press these buttons to set the room temperature. Press the [
] button to raise the room
temperature. Press the [
] button to lower the room
temperature. Keep pressing and the value will change more quickly
.
ECO Button Use this button to set the ECO ST
ART/ST
O
P
button
Press this button to start operation. Press it again to stop operation. T
ransmission sign
The transmission sign lights
up
when a signal is sent.
F
AN SPEED selector Button
This determines the fan speed. Every time you press
this button
the ang
e
from
(AUT
O)
(H
IG H)
(MED)
(LOW)
(SILENT) (This button allows
optimal or preferred
fan speed for each operation mode)
.
䇆
䇆
䇆
䇆
airflow rate will ch
selection of
This indicates the room temperature selected, current time, timer status, function and airflow rate selected.
mode.( p.18)
– 9 –
MODE SELECT
OR
AUT
O
HEA
T
DEHUMIDIFY COOL FA
N
F
AN SPEED
AUT
O
SILENT LOW MED HI ST
AR
T
/ ST
OP
ECO
Precautions for Use
ƽ
Do not put the remote controller in the following places.
ƽ
Under direct sunlight.
ƽ
In the vicinity of a heater
.
ƽ
Handle the remote controller carefully
. Do not drop it on the
floor
, and protect it from water
.
ƽ
Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power switch of
f and on or unplug the power cord and plug it in again).
This is to protect the device and does not indicate a failure.
ƽ
If you press the MODE selector button during operation, the device may stop for about 3 minutes for protection.
POWERFUL
Button
Use this button to set the POWERFUL
mode.
INFORMA
TION Button
ONE T
OUCH CLEAN Button
ON / OFF TIMER setting Buttons
MODE selector Button Use this button to select the
operating mode. Every time you press this button, the mode will change from
(AUT
O)
(HEA
T)
(DEHUMIDIFY)
(COOL) and
(F
AN)
cyclically
.
SILENT Button Use this button to set the SILENT
mode.
AUT
O
SWING (V
ertical) Button
Controls the angle of the
horizontal air deflector
.
WEEKL
Y
TIMER setting Buttons
LEA
VE HOME Button
NAMES AND FUNCTIONS OF REMOTE CONTROLLER
SLEEP
TIMER Button
Use this button to set the sleep timer
.
FA
N
POWERFUL SILENT INFO SLEEP
TIMER
AUT
O
SWING (VER
TICAL)
LEA
VE HOME
CLEAN DA
Y
PROGRAM NO.
ON / OFF
TIMER
TIME OK DELETE COPY
/ P
ASTE
CANCEL SEND CLOCK
( p.16)
( p.30
)
( p.20
)
( p.19) ( p.21)
( p.22)
( p.17)
( p.24)
( p.15)
FILTER lamp goes when the“ (AUTO SWING)” button is pressed while the device is on “STANDBY MODE”.
11