Hitachi M 12V2 Instruction Manual Download Page 10

Page: 10 / 10

Router Raizer Access Hole

.500" reference circle
for drilling table top or
insert plate.

1/2" = .500

Additional Templates Available on Website

2000-2006 Router Technologies

Hitachi

M12V2

Hitachi M12V2

Router table fence reference line

Router mounting holes

Use this 6" scale to check accuracy when copied

Drill .500" hole
through router
table insert plate

install #30 dust cover insert
into .500" hole and press flush
with top of insert plate

Router Raizer Access Hole

NOTE: This hole must be drilled 1/2" or .500"

for #30 dust cover insert to fit properly.

Note: Cross lines for locating and drilling holes are accurate. The illustration of subbase may vary
slightly in size and design, but is accurate enough for cutting the rubber spacer if required.

Page 25

Refer to pages 4,5,6, before using template

Summary of Contents for M 12V2











Search results

Summary of Contents for M 12V2

Reviews:

Related manuals for M 12V2

Brands by name

Popular brands

Hitachi M 12V2, Instruction Manual

Search results

Summary of Contents for M 12V2

Reviews:

Related manuals for M 12V2

Brands by name

Popular brands