background image

-4-

HOW TO USE TOOLS 

(Fig. 10, 11, 12)

Use the tools you require for cleaning hard floors, fabrics
and curtains etc.
1. Ensure the cleaner is in the upright position.
2. Hold the dusting brush 

8

 and the extension pipe 

9

 as

shown in Fig.10, and disconnect the dusting brush from
the extension pipe.

3. Turn the hose storage hook 

0

 counter clockwise, and

remove the flexible hose 

A

 from the back of the cleaner.

4. When use the extension pipes, remove them from the

back of the cleaner. The extension pipe assembly
consists of two pipes-with one located inside the other for
storage.

5. The tools can be connected as shown in Fig.12.

NOTE: 

After having finished using the tools, re-insert the

tools and restore the flexible hose on body.

NOTE: 

The extension pipes should be re-inserted as shown

in Fig.10.

NOTE: 

Rotary brush is not disconnected when tools are in

use and care should be taken not to run over the mains lead.

Fig.10

8

A

0

9

Fig.11

Fig.12

Using the dusting brush

Using the crevice  nozzle

Extension pipes

Curved joint
pipe

Dusting brush

Crevice  nozzle

CV_90CY.p65

6/28/04, 3:23 PM

5

Summary of Contents for CV-90CY













Reviews: