Hitachi CL2843S, Instruction Manual

Page: 14 / 18

ENGLISH - 46 -
Autostore
Autostore, searches and stores all channels automatically on
your TV, according to the transmission of programme systems
in your area.
$// 35(6725(' 352*5$00(6
:,// %( (5$6('
67$57
352*5$00(
67$1'$5' %*
3/($6( :$,7
3 9+)
&$1&(/
PROGRAMME item is used in order to store the channels af-
ter Autostore, as from a required programme. In default the pro-
gramme number is set to the following programme after the
last set programme. By using “ ” or “ ” button the number
can be changed, in addition to change number digit button or
double digit button can be used too.
Using “ ” or “ ” button on
STANDARD , you can change the
standard to B/G, D/K, L / L' .
To cancel AUTOSTORE before starting, press “
79
” button. To
select “ START ” use “ “ or “ ” button and press “ ” or “ ” but-
ton. To cancel AUTOSTORE during running press “ ” or “ ”
button.
After Autostore is finalized, a programme list will apper on the
screen. In the programme list you will see the programme
numbers and names assigned to the programmes.
If you do not accept the locations and/or the programme
names of programmes, you can change them in Programme
menu.
Other Features
TV Status
Programme Number , Programme Name ( or AV) , (they are
displayed on the upper left of the screen) and Sleep Timer
(shows the time left on the upper right screen if enabled). In
stereo options the sound indicator is displayed with them too.
They are displayed after programme change for 3 seconds.
Programme Number
Programme Name (5 characters)
These OSD’s are displayed when a new programme is en-
tered by digit button, by pressing “
P<P ” button, or by “ “ or “ ”
button, or by “ 79 ” button.
Programme Swap (P<P)
This button is used to reenter to the preceding entered pro-
gramme again. Pressing " P<P " consecutively allows to swap
into two last entered programmes.
Double-digit (- -)
This OSD is displayed when the “Double-Digit” button pressed
in place of the programme number indicator.
After that, in order to enter a programme press two digits con-
secutively. Both digits must be entered within 3 seconds
or the function will disappear.
Personal Preferences (PP)
All the preset values will be restored, when pressing " PP ".
Sound Indicator
This is a stereo option. The alternatives of the indicator are
Mono, Stereo, Dual I and Dual II. This indicator is displayed
under the programme number indicator on the screen. " I-II "
button is used to select Mono or Stereo, or Dual I or Dual II.
In Mono broadcast or in forced-mono (for stereo broadcast).
In Stereo broadcast.
If dual broadcast detected. Dual I is selected in default and also
can be selected after Dual II by Remote Control.
If Dual II selected by Remote Control.
Picture Mode
The picture mode OSD is displayed below the sound indica-
tor, by TV Status OSD’s. According to the WSS data, inside of
the OSD box “4:3”, “16:9” or “AUTO” is written.
By pressing “
” button (if Teletext is not active) the picture
mode can be switched into 4:3, 16:9 or Auto Mode.
Sleep Timer Last Minute Indicator
It is displayed on the upper right of the screen. If sleep timer is
activated it is displayed with the TV status and erased with it
after 3 seconds.
If there is only one minute of the countdown left of the timer, it
is displayed automatically on the upper left of the screen, and
stayed there until finishing. Then TV goes automatically to
stand-by.
Mute Indicator
It is placed in the upper middle of the screen when enabled,
and it stays there until it is disabled.
To cancel mute, there are two alternative; the first one is press-
ing to " " button, thus volume is set to the preceding value,
and the second one is increasing the volume level, thus it
starts at the minimum level to increase. By decreasing the
volume level in mute state, mute will not be ignored, only the
volume level will decrease. If mute is cancelled after decreas-
03-ENG-(CL2843S)-2872H-AV-3040-AK37-ST1P-VST.p65 26.06.2003, 11:42 46