24
TFT TV Service Manual
receivers use the latest generation of PanelLink TMDS core technology. These PanelLink cores pass
all HDMI compliancy tests.
11.22.2. Features
• HDMI 1.0 and DVI 1.0 compliant receiver
• Integrated PanelLink core supports DTV resolutions (480i/576i/480p/576p/720p/1080i)
• Digital video interface supports video processors:
o 24-bit RGB 4:4:4
o 24-bit YCbCr 4:4:4
o 16/20/24-bit YCbCr 4:2:2
o 8/10/12-bit YCbCr 4:2:2 embedded syncs
• Analog RGB and YPbPr output:
o 10-bit DAC
o Separate or Composite Syncs (Sync on G)
• S/PDIF output supports PCM, Dolby Digital, DTS digital audio transmission (32-48kHz Fs) using IEC
60958 and IEC 61937.
• Programmable I
2
S interface for connection to low-cost audio DACs.
• Integrated HDCP decryption engine for receiving protected audio and video content
• Pre-programmed HDCP keys provide highest level of key security, simplifies manufacturing
• Programmable registers via slave I
2
C interface
• 3.3V operation in 100-pin TQFP package
• Flexible power management
11.23. NCP1014
11.23.1. General
Description
The NCP101X series integrates a fixed
í
frequency current
í
modecontroller and a 700 V MOSFET.
Housed in a PDIP
í
7 or SOT
í
223package, the NCP101X offers everything needed to build a rugged
and low
í
cost power supply, including soft
í
start, frequency jittering, short
í
circuit protection, skip
í
cycle,
a maximum peak current setpoint and a Dynamic Self
í
Supply (no need for an auxiliary winding). Unlike
other monolithic solutions, the NCP101X is quiet by nature: during nominal load operation, the part
switches at one of the available frequencies (65
í
100
í
130 kHz). When the current setpoint falls below a
given value, e.g. the output power demand diminishes, the IC automatically enters the so
í
called skip
cycle mode and provides excellent efficiency at light loads. Because this occurs at typically 1/4 of the
maximum peak value, no acoustic noise takes place. As a result, standby power is reduced to the
minimum without acoustic noise generation. Short
í
circuit detection takes place when the feedback
signal fades away, e.g. in true short
í
circuit conditions or in broken Optocoupler cases. External
disabling is easily done either simply by pulling the feedback pin down or latching it to ground through
an inexpensive SCR for complete latched
í
off. Finally soft
í
start and frequency jittering further ease the
designer task to quickly develop low
í
cost and robust offline power supplies. For improved standby
performance, the connection of an auxiliary winding stops the DSS operation and helps to consume
less than100 mW at high line. In this mode, a built
í
in latched overvoltage protection prevents from
lethal voltage runaways in case the Optocoupler would brake.
11.23.2. Features
• Built
í
in 700 V MOSFET with Typical R
DSon
of 11
and 22
• Large Creepage Distance Between High
í
Voltage Pins
• Current
í
Mode Fixed Frequency Operation: 65 kHz–100 kHz
í
130 kHz
• Skip
í
Cycle Operation at Low Peak Currents Only: No Acoustic Noise!
• Dynamic Self
í
Supply, No Need for an Auxiliary Winding
• Internal 1.0 ms Soft
í
Start
• Latched Overvoltage Protection with Auxiliary Winding Operation
• Frequency Jittering for Better EMI Signature
• Auto
í
Recovery Internal Output Short
í
Circuit Protection
• Below 100 mW Standby Power if Auxiliary Winding is Used
• Internal Temperature Shutdown
• Direct Optocoupler Connection
• SPICE Models Available for TRANsient Analysis
Summary of Contents for 32LD8600
