Hisense HK316 User Manual Download Page 2

                                                             

 

Safety Notices Before Installation or Use 

☆ 

It is required grounded well and the supply voltage shall be stable, and you must confirm that 
the voltage of the outlet provides shall be in line with the voltage marked on the label of the 
unit.   

☆ 

Be sure not to sprinkle any liquid or fall any object into the unit. 

☆ 

Be sure not to keep heavy, strenuous movement, shake & heavy strike away from the POS. 

☆ 

Do not switch on or off the host frequently, because it is easy to result in damage on the 
machine. 

☆ 

Be sure not to unplug or plug in any live part or external device when they are in energized 
state, and the connecting cables of the POS between parts shall be connected securely.   

☆ 

Be sure neither to lengthen cable nor to replace parts at your will, if you have any demand, 
please contact with the reseller.   

☆ 

The unit shall be used under dry, ventilated & clean environment away from sunlight. Avoid to 
making the air vent of the host machine blocked or covered   

☆ 

If any liquid sprinkles or any sundry falls into the unit, please shut it down immediately & switch 
off power supply, take batteries down, dry the liquid or remove the sundry. If you take the 
batteries down, you shall reset CMOS. 

☆ 

In case of safety fault, such as peculiar smell, abnormal sound, leakage and other faults, you 
must switch off the power supply at once and then contact with reseller. 

☆ 

When inserting USB flash or disk, you shall kill virus to prevent the host machine from virus. 

☆ 

The RJ11 port at the back of the host is connected with the cash drawer, as it is not a 
communication port, users shall not use the port for dial-up networking.   

☆ 

The product is a Level A one, it may cause radio interference in living environment. In such case, 
users may need to take practical & feasible measures against the interference.   

☆ 

When the POS is not in use, you shall switch off power supply. 

 

 

 

 

 

 

 

 

The manufacturer has the right to modify the contents of the manual without prior notice!

   

Product standard NO

Q/0202 RSR527 

Product standard Name: POS device 

Warning: 

1.

 

Absolute Ratings of Environment

 

Operating Temperature

0

40

 

Operating Humidity

10%

85%RH 

Storage Temperature

-10

50

 

Storage Humidity

10%

90%RH 

2.

 

Main plug on the power supply was used as disconnected device. The socke
t-outlet shall be installed near the equipment and shall be easily accessible 

3.

 

If any damage to the power supply or the equipment, please contact local 
service person for help. 

4.    Static may damage to the integrated circuit in the host machine. 
5.    If a replaced battery is not right, this may cause explosion or serious 
damage. Must replace the same type of batteries or similar ones recommended 
by the manufacturer 
6.    Used only with attached AC/DC power supply. 

 

Summary of Contents for HK316



















Reviews: