manualshive.com logo in svg

HIOS PG Series, User Manual

Share
Download
HIOS PG Series User Manual Download Page 18

18

The login information is displayed.

❷

Disconnect button

This ends data import.

❸

Connect button

This makes the data import standby. If the previous data is necessary, please save the current data first 
and then connect the screwdriver. (The previous data will be cleared upon connection.)

❹

COM port

Check the port number and enter it. Then, press [Enter] on the keyboard. Usually, select COM as the 
port.
Cell colors

・

Gray: the screwdriver is not connected.

・

Yellow: the screwdriver is connected.

❺

LAN settings

Optional

❻

Judge On/Off

Errors E90/E91/E92 can be turned ON/OFF.
ON: the measured values are entered in the datasheet.
OFF: the measured values are entered in the irregular sheet.

❼

Measurement settings processing table

The table shows commands and settings processing that are displayed in the log.

❽

Judgment

This indicates OK/NG of screw tightening with colors.

❾

Output data

Torque equivalent value: this indicates values taken during actual operation.
Measurement time: this indicates the time from screw tightening to torque-up.
Number of the learning: indicates the number of teaching operations performed.
Minimum of the learning: indicates the minimum teaching value (modifiable).
Maximum of the learning: indicates the maximum teaching value (modifiable).
Measurement time of minimum: indicates the teaching minimum time (modifiable).
Measurement time of maximum: indicates the teaching maximum time (modifiable).
After inputting a number, press [Enter] on the keyboard.

・

These learning-related values will be sent to PG-01 by clicking the [Write learn-value] button after 

entering a number.

・

 If the [Learned value change] button is not pressed, the memory in PG-01 won’t be updated and the 
previous value will be recovered after the next torque-up operation.

❿

Judgment comparison data

Torque value: indicates the value output on the graph sheet.
Judgment minimum value: indicates the amount minus the % setting for the learning minimum value.
Judgment maximum value: indicates the amount plus the % setting for the learning maximum value.
Meas. Time of judge minimum: indicates the amount of the time minus the % setting for the learning 
minimum measurement time.
Meas. Time of judge maximum: indicates the amount of the time plus the % setting for the learning 
maximum measurement time.

⓫

Judgment error rate (%)

This sets the acceptable evaluation threshold before a screw tightening operation.

Summary of Contents for PG Series

























Reviews:

No comments

Brands by name

Popular brands

Load more brands