Hinkley 980007 Installation Instructions Manual Download Page 1

GENERAL INFORMATION

This wall remote control is designed to separately control your ceiling fan speed and light brightness.

      The fan button will control the fan speed. (Hi, Medium, Low)

      The light buttons will control the lights, brightness dimmer and off.

      The reverse button will control the fan forward or reverse.

      The red indicator on the transmitter will light when the button is pressed.

INSTALLATION AND OPERATING INSTRUCTIONS

NOTE: 

This wall remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units. 

The frequency switches on your receiver and transmitter have been preset at the factory.  Please recheck to make sure the switches on 

transmitter and receiver  are set  to  the same  position,  any combination of settings will operate the fan as long as the transmitter and 

receiver are set to the same position. 

1. SETTING THE CODE

This unit has 16 different code combinations. To set the code, perform these steps:

A.

Setting the code on the transmitter:

a. Slide the code switches to your choice of up or down position.  (Factory setting is all up). Do not use this Position.  Use a small screwdriver or a

ballpoint pen to slide firmly up or down (Figure A).

B.

Setting the code on the receiver:

a. Slide the code switches to the same positions as set on your transmitter (Figure B).

2. INSTALLING RECEIVER IN THE CEILING FAN

A.

Safety precautions:

WARNING:  HIGH VOLTAGE!

  Household electrical power can cause serious injury or death. Disconnect the source of electrical power

to the ceiling fan by removing the fuse or switching off the circuit breaker.

B.

Installing receiver in fan.:

a. Remove the ceiling fan canopy from the mounting bracket.

b. Disconnect the existing wiring between the ceiling fan and supply at the electrical junction box.

c. Lay the black antenna wire on top of the receiver, and put the receiver in the mounting bracket. (Fig. C)

d. Make the connections as follows, using the wire nuts supplied: (Fig. D)

CONNECT                                                    TO

           Green fan wire...........................................Bare supply wire

           Black receiver wire (AC IN L)..................Black supply wire

           White receiver wire(AC IN N)..................White supply wire

           White receiver wire (TO MOTOR N).......White fan wire

           Black receiver wire (TO MOTOR L)........Black fan wire

           Blue receiver wire(FOR LIGHT)..............Blue light wire

Code switches

Receiver

Fig. B

Transmitter

Fig. A

Fig. C

RECEIVER

Fig. D

AC SUPPLY

BLACK
WHITE

BARE

GREEN

WHITE

WHITE

BLUE

BLUE

BLACK

BLACK

RECEIVER

NOTE:

 When installing the remote 

control, be sure your fan control or 

pull chain switch are in the "

HIGH 

SPEED

" position and the light 

control or switch is set to "

ON

". 

Code switches

ON

ON

3 SPEED FAN & LIGHT

REMOTE CONTROL

INSTALLATION INSTRUCTIONS

Model: 980007

READ AND SAVE THESE INSTRUCTIONS

Control is for use with AC fans only 

Summary of Contents for 980007







Reviews: